1. Einführung und Endeview
The Skylink G6-T2 is a compact, two-button keychain transmitter designed to operate up to two compatible garage door openers. This device utilizes rolling code technology for enhanced security. Its small size allows for convenient carrying in a pocket or purse, or it can be mounted in a vehicle using the included accessories. The G6-T2 is compatible with Skylink EQ-IQ-Series Garage Door openers. For non-Skylink garage door openers, a Skylink Smart Button Receiver model GB-318 (sold separately) is required for operation.
Figure 1: Skylink G6-T2 Two-Button Keychain Transmitter (Black). This compact remote features two control buttons and a red indicator light.
2. Packungsinhalt
Überprüfen Sie, ob alle Artikel im Paket vorhanden sind:
- Skylink G6-T2 Two-Button Keychain Transmitter (available in assorted colors, including black and gray)
- One 12V Alkaline Battery (pre-installed or included separately)
- Visierklammer
- Montagezubehör
Figure 2: Skylink G6-T2 Transmitter shown alongside its included visor clip and mounting bracket.
3. Produktmerkmale
- Compact two-button design for keychain portability.
- Operates up to two Skylink EQ-IQ-Series Garage Door openers.
- Incorporates Rolling Code Technology for enhanced security.
- Includes a visor clip and additional mounting accessories for versatile placement.
- Powered by a long-life Alkaline battery (12V).
4. Einrichtung und Programmierung
The G6-T2 transmitter must be programmed to your garage door opener or a compatible receiver to function. The programming method varies depending on your specific garage door opener model or if you are using a Skylink Smart Button Receiver (GB-318).
4.1. Battery Installation/Verification
The G6-T2 uses one 12V Alkaline battery. Ensure the battery is correctly installed and functional before programming. If the red indicator light on the transmitter does not illuminate when a button is pressed, the battery may need replacement (refer to Section 6).
4.2. Programming to a Skylink EQ-IQ-Series Garage Door Opener
- Suchen Sie die Lernen button on your Skylink EQ-IQ-Series garage door opener motor unit. The location of this button may vary; consult your garage door opener's instruction manual for precise details.
- Drücken und loslassen der Lernen button on the garage door opener. The indicator light on the opener will typically illuminate or flash, indicating it is in programming mode.
- Within 30 seconds, press and hold the desired button on your G6-T2 transmitter for approximately 2-3 seconds.
- Release the button. The garage door opener's light may flash or turn off, indicating successful programming.
- Testen Sie den Sender, indem Sie die programmierte Taste drücken. Das Garagentor sollte sich öffnen.
4.3. Programming with a Skylink Smart Button Receiver (GB-318)
If your garage door opener is not a Skylink EQ-IQ-Series model, you will need a Skylink Smart Button Receiver (GB-318) to enable compatibility with the G6-T2 transmitter. Refer to the instruction manual provided with your GB-318 receiver for specific programming steps. Generally, the process involves:
- Ensure the GB-318 receiver is properly installed and connected to your garage door opener.
- Activate the programming mode on the GB-318 receiver (usually by pressing a Lernen Taste).
- Press the desired button on your G6-T2 transmitter to pair it with the GB-318.
- Testen Sie die Funktion.
Wichtig: Always refer to the specific instruction manual for your garage door opener or the Skylink Smart Button Receiver (GB-318) for detailed and accurate programming procedures.
5. Bedienung
Once programmed, operating the G6-T2 transmitter is straightforward:
- Press the programmed button on the transmitter to activate your garage door opener.
- The red indicator light on the transmitter will illuminate briefly when a button is pressed, confirming signal transmission.
- If two garage door openers are programmed, use the corresponding button for each opener.
6. Batteriewechsel
The G6-T2 transmitter is powered by one 12V Alkaline battery. If the operating range decreases significantly or the red indicator light does not illuminate when a button is pressed, it is time to replace the battery.
Ersetzungsverfahren:
- Öffnen Sie vorsichtig die casing of the G6-T2 transmitter. This may involve gently prying apart the two halves of the remote, often at a seam.
- Entfernen Sie die alte 12V-Alkaline-Batterie.
- Insert a new 12V Alkaline battery, ensuring the correct polarity (+ and -) is observed.
- Schnapp dir das Casing wieder sicher zusammenfügen.
- Test the transmitter to ensure proper function.
Notiz: Entsorgen Sie alte Batterien entsprechend den örtlichen Vorschriften.
7. Fehlerbehebung
| Problem | Mögliche Ursache | Lösung |
|---|---|---|
| Der Sender aktiviert das Garagentor nicht. | Not programmed correctly; Dead or low battery; Out of range; Incompatible opener. | Re-program the transmitter (Section 4); Replace battery (Section 6); Move closer to the garage door opener; Ensure compatibility or use GB-318 receiver. |
| Die rote Kontrollleuchte leuchtet nicht. | Batterie defekt oder falsch eingebaut. | Replace battery, ensuring correct polarity (Section 6). |
| Reduzierter Betriebsbereich. | Low battery; Radio interference. | Replace battery (Section 6); Check for sources of interference near the garage door opener. |
| Transmitter works intermittently. | Low battery; Weak signal; Interference. | Replace battery (Section 6); Ensure clear line of sight to opener; Check for interference. |
8. Spezifikationen
| Modellnummer | G6-T2 |
| Marke | SKYLINK |
| Abmessungen (L x B x H) | 2.5 x 1.5 x 0.75 Zoll |
| Gewicht | 1.83 Unzen |
| Akku-Typ | 1 x 12 V Alkali (im Lieferumfang enthalten) |
| Durchschnittliche Akkulaufzeit | 4320 Stunden |
| Kompatibilität | Skylink EQ-IQ-Series Garage Door openers, Skylink Smart Button Receiver model GB-318 |
| Technologie | Rollender Code |
| Farbe | Assorted (e.g., Gray, Black) |
9. Garantie und Support
9.1. Garantieinformationen
The Skylink G6-T2 Two-Button Keychain Transmitter comes with a 1-year limited warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. It does not cover damage resulting from misuse, accident, alteration, or unauthorized repair.
9.2. Kundendienst
For technical assistance, troubleshooting beyond this manual, or warranty claims, please contact Skylink customer support. Refer to the official Skylink webAktuelle Kontaktinformationen finden Sie auf der Website oder der Produktverpackung.