MOOG 513346 Wheel Bearing and Hub Assembly Instruction Manual

1. Einleitung

This manual provides essential information for the MOOG 513346 Wheel Bearing and Hub Assembly. This component is engineered to deliver reliable performance and facilitate straightforward installation in compatible Ford Mustang vehicles. It features an advanced raceway design for extended service life and coated wheel studs for rust protection.

Abbildung 1: Vorderseite view of the MOOG 513346 Wheel Bearing and Hub Assembly.

Abbildung 2: Rückseite view of the MOOG 513346 Wheel Bearing and Hub Assembly.

2. Kompatibilität

The MOOG 513346 Wheel Bearing and Hub Assembly is compatible with the following Ford Mustang models:

• 2015-2015 Ford Mustang
• 2016-2020 Ford Mustang
• 2016-2017 Ford Mustang
• 2021-2021 Ford Mustang

Wichtig: Vor dem Kaufasing and installing, verify compatibility with your specific vehicle by checking the manufacturer's fitment guide or consulting a qualified automotive professional.

3. Sicherheitshinweise

Automotive repair can be hazardous. Always prioritize safety. It is recommended that installation be performed by a certified mechanic or an individual with appropriate automotive repair experience.

• Tragen Sie geeignete persönliche Schutzausrüstung, einschließlich Schutzbrille und Handschuhen.
• Stellen Sie sicher, dass das Fahrzeug vor Beginn jeglicher Arbeiten sicher auf Unterstellböcken steht. Verlassen Sie sich niemals ausschließlich auf einen Wagenheber.
• Use the correct tools for each step of the installation process.
• Detaillierte Anweisungen und Drehmomentvorgaben finden Sie in der spezifischen Bedienungsanleitung Ihres Fahrzeugs.
• Halten Sie Kinder und Haustiere vom Arbeitsbereich fern.

4. Enthaltene Komponenten

Jedes Paket enthält:

• One (1) MOOG 513346 Wheel Bearing and Hub Assembly

Figure 3: Key components of the MOOG Wheel Bearing and Hub Assembly.

5. Installationsrichtlinien

The MOOG 513346 Wheel Bearing and Hub Assembly is designed for fast and hassle-free installation. However, specific steps may vary depending on your vehicle's configuration. Always consult your vehicle's factory service manual for detailed, model-specific instructions.

Allgemeine Installationsschritte (Einzelheiten siehe Fahrzeughandbuch):

1. Das Fahrzeug sicher anheben und abstützen. Das Rad abnehmen.
2. Remove the brake caliper and rotor.
3. Disconnect any ABS sensor wiring if present.
4. Remove the axle nut. A 35mm socket and a large breaker bar are typically required for this step.
5. Remove the bolts securing the old hub assembly to the steering knuckle.
6. Carefully remove the old hub assembly.
7. Clean the mounting surface on the steering knuckle.
8. Install the new MOOG hub assembly, ensuring proper alignment. The coated wheel studs inhibit rust for easier removal and proper torqueing.
9. Tighten the hub assembly bolts to the manufacturer's specified torque.
10. Install the new axle nut and tighten to the manufacturer's specified torque. A torque wrench capable of 250 ft-lb is often needed for the axle nut.
11. Schließen Sie die Verkabelung des ABS-Sensors wieder an.
12. Reinstall the brake rotor and caliper.
13. Montieren Sie das Rad wieder und senken Sie das Fahrzeug ab.

Figure 4: Illustration of wheel installation, highlighting the ease of assembly.

6. Betriebsmerkmale

Once installed, the MOOG 513346 Wheel Bearing and Hub Assembly contributes to the safe and smooth operation of your vehicle's wheel system. Its application-specific advanced raceway design is engineered to reduce stress, rotation, and heat on components, thereby extending service life and maintaining optimal performance.

Figure 5: Cross-section illustrating the durable raceway design for extended service life.

7. Wartung

Wheel bearing and hub assemblies are critical components that require minimal direct maintenance after proper installation. However, regular inspection during tire rotations or brake service is recommended.

• Inspektion: Periodically check for signs of wear, such as excessive play in the wheel, unusual noises, or visible damage to the hub assembly or its seals.
• Schmierung: This assembly is designed to be maintenance-free with factory-sealed lubrication (grease). No additional lubrication is typically required.
• Korrosionsschutz: The coated wheel studs are designed to resist corrosion, aiding in easier future removal and proper torqueing.

Figure 6: Coated wheel studs for enhanced corrosion protection.

8. Fehlerbehebung

If you suspect an issue with your wheel bearing and hub assembly, observe the following common symptoms:

• Ungewöhnliches Geräusch: A humming, grinding, or growling noise that increases with vehicle speed.
• Vibration: Vibrations felt through the steering wheel or floorboard, especially at certain speeds.
• ABS Light: Illumination of the Anti-lock Braking System (ABS) warning light on the dashboard.
• Spiel in der Lenkung: A feeling of looseness or excessive play in the steering.

If any of these symptoms occur, it is crucial to have your vehicle inspected by a qualified mechanic immediately to prevent further damage or safety risks.

Figure 7: Symptom - Vehicle Noise/Vibration

Figure 8: Symptom - Steering Wheel Vibration

Figure 9: Symptom - ABS Warning Light

9. Spezifikationen

Figure 10: MOOG components undergo rigorous testing for reliability.

10. Garantieinformationen

For detailed warranty information regarding the MOOG 513346 Wheel Bearing and Hub Assembly, please refer to the official MOOG website or contact your point of purchase. Warranty terms and conditions may vary.

11. Unterstützung

If you require technical assistance, have questions about installation, or need further support, please contact MOOG customer service or consult a certified automotive technician.

Weitere Informationen und Kontaktdaten finden Sie auf der offiziellen Website. MOOG Store.