SOMMER Pearl 4018 Garage Door Remote Control User Manual

1. Einleitung

This manual provides instructions for the safe and efficient operation, setup, and maintenance of your SOMMER Pearl 4018 4018V000 TX55-868-4 garage door remote control. This device utilizes the SOMloq2 radio system and is compatible with Somloq Rollingcode systems, as well as Pro Teckentrup Drive models 4020, 4026, and 4031 Slider.

Abbildung 1: SOMMER Pearl 4018 4018V000 TX55-868-4 Remote Control. This image shows the compact, modern design of the remote control, featuring four buttons and a stainless steel application.

2. Sicherheitshinweise

• Keep the remote control out of reach of children to prevent accidental operation of the garage door.
• Do not allow children to play with the remote control or the garage door opener.
• Vor der Bedienung sicherstellen, dass das Garagentor gut sichtbar und frei von Hindernissen ist.
• Do not operate the garage door if people or objects are in its path.
• Batterien sind gemäß den örtlichen Vorschriften zu entsorgen. Batterien dürfen nicht verbrannt werden.
• Avoid exposing the remote control to extreme temperatures, moisture, or direct sunlight.

3. Packungsinhalt

Überprüfen Sie, ob alle Artikel in Ihrem Paket vorhanden sind:

• SOMMER Pearl 4018 4018V000 TX55-868-4 Remote Control (quantity as purchased, typically 2 units)
• 3V CR2032 Lithium-metal battery (pre-installed or included)

4. Einrichtung und Programmierung

The SOMMER Pearl 4018 remote control must be programmed to your garage door opener receiver. The exact programming steps may vary slightly depending on your specific SOMMER garage door opener model. Refer to your garage door opener's manual for precise instructions. A common programming method is outlined below:

1. Empfänger lokalisieren: Identify the garage door opener's motor unit. On the motor unit, locate the "Learn" or "Program" button. This button is often small and may be recessed.
2. Lernmodus aktivieren: Press and immediately release the "Learn" or "Program" button on your garage door opener. The indicator light on the opener will typically illuminate or flash, indicating it is in learn mode. You usually have about 30 seconds to complete the next step.
3. Fernbedienung programmieren: Within the learn mode timeframe, press and hold the desired button on your SOMMER Pearl 4018 remote control that you wish to use for operating the garage door.
4. Programmierung bestätigen: Release the button on the remote control once the garage door opener's indicator light flashes or changes color, or if the garage door moves slightly. This indicates successful programming.
5. Testbetrieb: Press the programmed button on your remote control to ensure it operates the garage door correctly.
6. Zusätzliche Fernbedienungen programmieren: Repeat these steps for any additional SOMMER Pearl 4018 remote controls you wish to program.

Note: If your garage door opener has a different programming procedure (e.g., using a master remote or a specific sequence), please consult your opener's manual.

5. Bedienungsanleitung

Once programmed, operating your SOMMER Pearl 4018 remote control is straightforward:

• Öffnen/Schließen der Tür: Press the programmed button on your remote control once. The garage door will begin to open or close.
• Die Tür anhalten: Press the same programmed button again while the door is in motion to stop it.
• Mehrere Türen: If you have programmed multiple garage doors to different buttons on your remote, press the corresponding button for the desired door.
• Reichweite: The remote control has an approximate range of 50-140 meters, depending on environmental conditions and obstructions.

6. Wartung

6.1. Batteriewechsel

The SOMMER Pearl 4018 remote control uses a 3V CR2032 Lithium-metal battery. When the remote's range decreases significantly or it stops responding, it is likely time to replace the battery.

1. Öffne das Casing: Öffnen Sie vorsichtig die Fernbedienung casing. This usually involves prying it open with a small flat-head screwdriver or a similar tool at a designated notch.
2. Alte Batterie entfernen: Note the orientation of the old CR2032 battery (positive (+) side up or down). Gently remove the old battery.
3. Neue Batterie einlegen: Insert a new 3V CR2032 Lithium-metal battery, ensuring the correct polarity. The positive (+) side typically faces upwards.
4. Schließen Sie Casing: Schnapp dir die Fernbedienung casing wieder sicher zusammenfügen.
5. Prüfen: Testen Sie die Fernbedienung, um sicherzustellen, dass sie mit der neuen Batterie einwandfrei funktioniert.

6.2. Reinigung

Clean the remote control with a soft, dry cloth. Do not use abrasive cleaners or allow moisture to enter the casing.

7. Fehlerbehebung

8. Spezifikationen

• Modell: Pearl 4018 4018V000 TX55-868-4
• Funksystem: SOMloq2
• Tasten: 4
• Radiofrequenz: FM 868.8 MHz, FM 868.95 MHz
• Reichweite: Approx. 50-140 meters (environment dependent)
• Abmessungen: 79 x 26 x 13 mm (3.11 x 1.02 x 0.51 Zoll)
• Akku-Typ: 3V CR2032 Lithium-metal
• Gewicht: 40 g
• Kompatibilität: Somloq Rollingcode system, Pro Teckentrup Drive (compatible with 4020, 4026, 4031 Slider)

9. Garantie und Support

For warranty information and technical support, please refer to the documentation provided with your original purchase or contact SOMMER customer service directly. Contact details can typically be found on the manufacturer's official webWebsite.