Herdio 5.25'' Home Audio Package Wall Mount Bluetooth Amplifier Receiver System with In-Ceiling Wall Passive Speakers (Model HCS 528-16BT) Instruction Manual

1. Sicherheitshinweise

Bitte lesen Sie alle Sicherheitshinweise sorgfältig durch, bevor Sie dieses Produkt installieren oder in Betrieb nehmen. Die Nichtbeachtung dieser Hinweise kann zu Stromschlag, Brand oder anderen Gefahren führen.

• Energiequelle: Verwenden Sie ausschließlich das mitgelieferte Netzteil. Stellen Sie sicher, dass die Spannung des Netzteilstage entspricht den Produktanforderungen.
• Wasser und Feuchtigkeit: Do not expose this product to water, moisture, or extreme humidity. Avoid installation in areas where water contact is possible.
• Hitze: Do not install near heat sources such as radiators, heat registers, stoves, or other apparatus that produce heat.
• Belüftung: Sorgen Sie für ausreichende Belüftung um das amplifier unit. Do not block any ventilation openings.
• Installation: Installation should be performed by qualified personnel following local electrical codes. Ensure all wiring is secure and properly insulated.
• Reinigung: Disconnect power before cleaning. Use a dry cloth only. Do not use liquid cleaners or aerosol cleaners.
• Wartung: Versuchen Sie nicht, dieses Produkt selbst zu warten. Überlassen Sie alle Wartungsarbeiten qualifiziertem Servicepersonal.

2. Produktüberschreitungview

The Herdio 5.25'' Home Audio Package provides a versatile sound solution for various indoor environments. It includes a wall-mount Bluetooth amplifier receiver and two 5.25-inch in-ceiling passive speakers. The system supports multiple audio input options, including Bluetooth, AUX, and USB, along with a microphone input for paging or announcements.

2.1. Wall Mount Bluetooth Amplifier-Empfänger

Dieses kompakte amplifier unit is designed to fit into a standard wall plate, offering convenient access to controls and connectivity. It features a master volume knob, input selection switch, USB port for media playback and device charging, a 3.5mm AUX-in jack, and a 1/4'' MIC-in jack.

Abbildung 1: Wandhalterung Amplifier Controls. This image displays the front panel of the wall-mount amplifier, detailing the power LED, input selection switch (AUX, BT, MIC), USB port, master volume/power knob, MIC IN jack, and AUX IN jack.

Figure 2: USB Interface. This image shows a USB flash drive inserted into the USB input port on the wall-mount amplifier, illustrating its function for media playback or device charging.

2.2. 5.25-inch In-Ceiling Passive Speakers

The system includes two 5.25-inch passive speakers designed for flush mounting in ceilings or walls. These speakers are engineered to reproduce clear sound with good responsiveness, suitable for various audio applications.

Figure 3: In-Ceiling Speaker Design. This image highlights the speaker's design, emphasizing its powerful bass capabilities and integrated coaxial tweeter for balanced audio output.

3. Lieferumfang

Packen Sie den Inhalt vorsichtig aus und vergewissern Sie sich, dass alle Artikel vorhanden sind:

• 1x Bluetooth In-Wall Audio Receiver Wall Plate
• 1x 12V Netzteil
• 2x Screws for Wall Plate Installation
• 2x 5.25-inch In-Ceiling Speakers (Model HCS-528)
• 2x Speaker Wires
• 1x User Manual for Ampschwerer
• 1x User Manual for Speakers
• 2x Gaskets for Speakers
• 1x Cutout Template for Speakers

Figure 4: Package Contents. This image displays all components included in the Herdio 5.25'' Home Audio Package, laid out for verification.

4. Einrichtung

4.1. Wandhalterung Amplifier-Installation

1. Bereiten Sie die Wand vor: Ensure you have a standard electrical wall box available for installation.
2. Netzkabel anschließen: Connect the 12V DC power cable (red positive, black negative) to the two-pin connector on the back of the amplifier-Modul.
3. Audiokabel anschließen: Connect the stereo input audio cable to the three-pin connector on the back of the amplifier-Modul.
4. Montieren Sie die AmpReiniger: Führen Sie die amplifier module into the wall box. Secure it using the provided screws.
5. Frontplatte anbringen: Place the decorative faceplate over the amplifier and secure it.

Abbildung 5: Wandhalterung Amplifier Installation. This image illustrates the process of installing the wall-mount amplifier into a standard electrical box.

4.2. Ceiling Speaker Installation

1. Standort bestimmen: Choose appropriate locations in the ceiling or wall for the speakers, ensuring no obstructions behind the surface.
2. Schnittöffnung: Use the provided cutout template to mark and cut a circular opening in the ceiling/wall. The cutout diameter is 7.3 inches (18.5 cm).
3. Remove Speaker Grille: Gently remove the speaker grille using a small tool or screwdriver.
4. Lautsprecher einfügen: Setzen Sie den Lautsprecher in die Aussparung ein.
5. Lautsprecher sichern: Tighten the speaker clips with screws to firmly secure the speaker in place.
6. Replace Grille: Carefully place the speaker grille back onto the speaker.

Figure 6: Installation Dimensions. This diagram provides the total speaker diameter (8.46 inches / 21.5 cm), cutout diameter (7.3 inches / 18.5 cm), speaker depth (4.33 inches / 11 cm), and wall plate dimensions (4.5 inches / 11.43 cm height, 2.75 inches / 6.89 cm width).

Figure 7: Removing Speaker Grille. This image shows how to carefully remove the speaker's protective grille.

Figure 8: Securing Speaker Clips. This image demonstrates tightening the speaker clips with screws to ensure a secure fit in the ceiling or wall.

Figure 9: Replacing Speaker Grille. This image shows the final step of placing the speaker grille back onto the installed speaker.

4.3. Verdrahtung des Systems

1. Connect Speaker Wires to Speakers: Connect the provided speaker wires to the terminals on the back of each speaker. Ensure red wire connects to positive (+) and black wire to negative (-).
2. Schließen Sie die Lautsprecherkabel an AmpReiniger: Connect the other end of the speaker wires to the speaker output terminals on the back of the wall-mount amplifier. Use a screwdriver to loosen the terminal screws, insert the wires (red to SPK+, black to SPK-), and tighten the screws to secure the connection.
3. Stromversorgung anschließen: Plug the 12V power supply into a standard electrical outlet and connect its DC plug to the 12V DC input jack on the wall-mount ampschwerer.

5. Bedienungsanleitung

5.1. Ein-/Ausschalten und Lautstärkeregelung

To power on the system, turn the master volume knob clockwise. You will hear an audible 'drop' sound, and the power LED (PWR) will illuminate. Continue turning the knob clockwise to increase the volume. To power off, turn the knob counter-clockwise until it clicks.

5.2. Eingabeauswahl

Use the input selection switch on the amplifier's front panel to choose between AUX, BT (Bluetooth), or MIC inputs.

5.3. Bluetooth-Kopplung

1. Switch the input selector to 'BT'. The Bluetooth LED will flash, indicating it is in pairing mode.
2. Aktivieren Sie auf Ihrem Mobilgerät (Smartphone, Tablet usw.) Bluetooth und suchen Sie nach verfügbaren Geräten.
3. Select 'Herdio' from the list of available devices to pair.
4. Once successfully paired, the Bluetooth LED on the amplifier will remain steadily lit.
5. You can now play audio from your device through the Herdio speaker system.

5.4. Using USB Input

Insert a USB flash drive into the USB INPUT port for media playback. The ampDer Verstärker erkennt und spielt Audio automatisch ab. files. This port also functions as a charging port for compatible devices (5V/1A).

5.5. Using AUX-In

Connect an external audio device (e.g., MP3 player, TV) to the 3.5mm AUX IN jack using a stereo audio cable. Switch the input selector to 'AUX' to play audio from the connected device.

5.6. Using MIC-In

Connect a microphone to the 1/4'' MIC IN jack. Switch the input selector to 'MIC' for microphone input. This feature is suitable for paging or making announcements.

6. Wartung

To ensure the longevity and optimal performance of your Herdio audio system, follow these maintenance guidelines:

• Reinigung: Reinigen Sie die amplifier faceplate and speaker grilles. Avoid abrasive cleaners, solvents, or harsh chemicals.
• Staubentfernung: Die Lautsprechergitter sollten regelmäßig abgestaubt werden, um Ablagerungen zu vermeiden, die die Klangqualität beeinträchtigen könnten.
• Umgebungsbedingungen: Keep the system in a dry environment, away from direct sunlight, extreme temperatures, and excessive dust.
• Verkabelungsprüfung: Periodically check all wiring connections for tightness and signs of wear. Loose connections can lead to poor sound quality or intermittent operation.

7. Fehlerbehebung

If you encounter issues with your Herdio audio system, refer to the following common problems and solutions:

8. Spezifikationen

9. Garantie und Support

This Herdio product is covered by a 1 Jahre Servicegarantie Ab Kaufdatum. Diese Garantie deckt Herstellungsfehler und Verarbeitungsfehler bei normalem Gebrauch ab.

Von der Garantie ausgeschlossen sind Schäden, die verursacht werden durch:

• Unsachgemäße Installation oder Bedienung.
• Accidents, misuse, abuse, or negligence.
• Unbefugte Reparaturen oder Änderungen.
• Power surges or lightning strikes.

For warranty claims, technical support, or customer service, please contact Herdio customer support through your retailer or visit the official Herdio webWebsite für Kontaktinformationen.