UMLIFE 20A Brushed ESC Instruction Manual

Einführung

Thank you for choosing the UMLIFE 20A Brushed Electronic Speed Controller (ESC). This manual provides essential information for the safe and efficient operation of your ESC. This device is designed for use with various RC models, including cars, boats, and tanks, offering precise motor control with forward, reverse, and brake capabilities.

Sicherheitshinweise

• Um ein versehentliches Einschalten und mögliche Schäden zu vermeiden, sollte der Akku des Reglers immer vom Regler getrennt werden, wenn dieser nicht verwendet wird.
• Ensure all connections are secure and correctly polarized before applying power. Incorrect wiring can damage the ESC, motor, or battery.
• RC-Modelle sollten nur im Freien, fernab von Menschen, Tieren und Hindernissen, betrieben werden.
• Überschreiten Sie nicht das angegebene Volumentage and current ratings. Overloading can lead to overheating and permanent damage.
• Keep the ESC away from water and moisture unless specifically designed for waterproof operation.
• Für Benutzer unter 14 Jahren wird die Aufsicht durch Erwachsene empfohlen.

Produkteigenschaften

• Aktuelle Bewertung: Constant 20A, Maximum 25A (<30s), Pulsed 50A (<5s).
• Betriebslautstärketage: 4.8V - 8.4V (compatible with 2S LiPo batteries).
• Antriebsfrequenz: 2kHz.
• Motorkompatibilität: Supports 130, 180, 260, 280, and 380 brushed motors.
• Funktionen: Forward, Reverse, and Brake.
• BEC-Ausgang: 5.7V, 1A (for receiver/servo power).
• Kompaktes Design: Lightweight and suitable for various mini RC applications.

Packungsinhalt

• 4 x UMLIFE 20A Brushed ESC Units

Einrichtung und Verkabelung

Proper wiring is crucial for the correct function and longevity of your ESC. Refer to the diagram below for connection points.

Bild: Wiring diagram for the 20A Brushed ESC. This image illustrates the connection points for the signal line (to receiver), battery interface (power input), motor interface (power output to motor), and the physical switch for power on/off. It also highlights the "With/without brake switch" setting on the ESC board.

1. Anschluss an den Receiver: Plug the signal line (black, red, white wires) from the ESC into the throttle channel of your RC receiver. The white wire is typically signal, red is positive (BEC output), and black is negative.
2. An die Batterie anschließen: Connect your battery pack to the battery interface (red and black wires with a connector, typically JST or similar). Ensure correct polarity: red to positive (+), black to negative (-). The ESC supports 2S LiPo or 4-7 cell Ni-MH/Ni-Cd batteries (4.8V-8.4V). Do not use 3S LiPo batteries as this can damage the ESC.
3. Anschluss an den Motor: Connect your brushed motor to the motor interface (red and black wires). The polarity here determines the motor's rotation direction. If the motor spins in the wrong direction, reverse the motor wires. The ESC is compatible with 130, 180, 260, 280, and 380 brushed motors.
4. Brake Switch Setting: The ESC features a small switch on the board to enable or disable the brake function. Adjust this switch according to your preference for braking behavior. Refer to the image for the location of this switch.
5. Stromschalter: Use the external power switch to turn the ESC on or off.

Bedienungsanleitung

Sobald alle Verbindungen hergestellt und überprüft sind:

1. Schalten Sie zuerst Ihren RC-Sender ein.
2. Then, turn on the power switch on the ESC.
3. The ESC will initialize. Wait for any calibration tones or LED indicators to confirm it's ready.
4. Use the throttle stick on your transmitter to control the motor.
   • Nach vorne: Push the throttle stick forward.
   • Umkehren: Pull the throttle stick backward from the neutral position.
   • Bremse: If the brake function is enabled via the onboard switch, moving the throttle stick to neutral after a forward or reverse input will engage the brake.
5. After operation, turn off the ESC power switch first, then turn off your transmitter.

Wartung

• Keep the ESC clean and free from dust, dirt, and debris.
• Regularly inspect all wires and connectors for signs of wear or damage. Replace any damaged components immediately.
• Bewahren Sie den ESC bei Nichtgebrauch in einer trockenen, kühlen Umgebung auf.
• Vermeiden Sie es, den ESC über längere Zeiträume extremen Temperaturen oder direkter Sonneneinstrahlung auszusetzen.

Fehlerbehebung

• Motor reagiert nicht:
  • Check all wiring connections (battery, motor, receiver signal).
  • Ensure the battery is charged and connected with correct polarity.
  • Verify the transmitter is on and properly bound to the receiver.
  • Confirm the motor is compatible with the ESC (brushed type, within current limits).
• Motor spins in wrong direction:
  • Reverse the two motor wires connected to the ESC.
• No brake function:
  • Check the position of the onboard brake switch. Ensure it is set to the "with brake" position.
  • Verify your transmitter's throttle trim and sub-trim settings are centered.
• ESC or motor overheating:
  • Ensure the motor is not undersized for the application or experiencing excessive load.
  • Check for any binding in the drivetrain that could cause extra strain.
  • Bestätigen Sie die Batterielautstärketage is within the specified range (4.8V-8.4V). Using higher voltage (e.g., 3S LiPo) will damage the ESC.

Technische Daten

Garantie und Support

Informationen zu Garantie, technischem Support oder Serviceanfragen erhalten Sie beim Hersteller oder Ihrer Verkaufsstelle. Bewahren Sie Ihren Kaufbeleg als Kaufnachweis auf.