Einführung
Thank you for choosing the DotMod Switch R Pods. These high-quality replacement tanks are designed to perfectly complement your DotMod Switch R Stick, providing an optimal performance and a premium vaping experience. With an integrated atomizer head and a generous 3ml filling volume, you can enjoy your favorite e-liquids for extended periods without frequent refills. DotMod Switch R Pods are easy to install and deliver reliable, flavor-intensive vapor production.
Wichtige Sicherheitsinformationen
Haftungsausschluss: This product is nicotine-free and does not contain any liquids. Keep out of reach of children and pets. Store in a cool, dry place away from direct sunlight.
Produkt überview
The DotMod Switch R Pods are designed for ease of use and optimal performance. Each pod features a pre-installed coil and a side-fill system for convenient refilling.
Image: Two DotMod Switch R Pods. This image displays two pods side-by-side, highlighting their transparent body, the "dot." logo, the 0.8 Ohm resistance marking, and the red "OPEN" tab for the side-fill port. The CE and recycling symbols are also visible at the bottom.
Image: Single DotMod Switch R Pod. This image provides a closer look at a single pod, emphasizing the red "OPEN" tab for the side-fill mechanism and the clear indication of the 0.8 Ohm resistance.
Abbildung: Seite view of DotMod Switch R Pod. This image shows the pod from a slightly different angle, highlighting the shape of the mouthpiece and the location of the side-fill port.
Aufstellen
Füllen der Kapsel
- Remove the pod from your DotMod Switch R Stick.
- Locate the red "OPEN" tab on the side of the pod. Gently lift or slide this tab to reveal the filling port.
- Stecken Sie die Düse Ihrer E-Liquid-Flasche in die Einfüllöffnung.
- Carefully fill the pod with up to 3ml of your preferred e-liquid. Avoid overfilling.
- Close the red tab securely to prevent leaks.
- After filling a new pod, wait at least 5-10 minutes before vaping to allow the coil to become fully saturated with e-liquid. This is known as "priming" the coil and helps prevent dry hits and extends coil life.
Installieren des Pods
- Ensure the pod is properly filled and the fill port is closed.
- Align the bottom of the pod with the pod slot on your DotMod Switch R Stick.
- The pod will snap into place magnetically. Ensure it is seated firmly.
Betrieb
Once the pod is filled and installed, your DotMod Switch R Stick is ready for use. The device typically operates via an auto-draw mechanism or a fire button, depending on your specific DotMod Switch R model.
- Dampfen: Inhale through the mouthpiece to activate the device (auto-draw) or press and hold the fire button while inhaling.
- Monitoring E-liquid Level: The transparent design of the pod allows you to easily monitor your e-liquid level. Refill the pod before it runs completely dry to prevent coil damage.
Wartung
Pod-Ersatz
The DotMod Switch R Pods feature a fixed, non-replaceable coil. When you notice a decrease in flavor, vapor production, or a burnt taste, it's time to replace the entire pod.
- Remove the old pod from your DotMod Switch R Stick.
- Dispose of the old pod responsibly according to local regulations.
- Install a new, pre-filled or freshly filled pod as described in the "Setup" section.
Reinigung
- Periodically clean the contact points on both the pod and your DotMod Switch R Stick with a dry cotton swab or tissue to ensure good connectivity.
- Wipe down the exterior of the pod with a clean, damp cloth if necessary. Do not submerge the pod in water.
Fehlerbehebung
| Problem | Mögliche Ursache | Lösung |
|---|---|---|
| Kein oder nur schwacher Dampf | Low e-liquid level; Poor connection; Coil burnt out; Device battery low. | Refill pod; Clean contact points; Replace pod; Charge device battery. |
| Verbrannter Geschmack | Coil not primed; E-liquid level too low; Coil burnt out. | Ensure proper priming (wait 5-10 min after filling); Refill pod; Replace pod. |
| Undicht | Overfilling; Fill port not closed properly; Damaged pod. | Do not overfill; Ensure fill tab is securely closed; Replace pod if damaged. |
Technische Daten
| Besonderheit | DotMod Switch R Pod 0.6 Ohm | DotMod Switch R Pod 0.8 Ohm |
|---|---|---|
| Material | PCTG | PCTG |
| Verbindung | Magnetic Plug&Play | Magnetic Plug&Play |
| Füllvolumen | 3 ml | 3 ml |
| Spulentyp | Fixed, 0.6 Ohm Mesh | Fixed, 0.8 Ohm Mesh |
| Empfohlenes Wattage | 23 Watt | 18 Watt |
| Füllsystem | Seitenfüllsystem | Seitenfüllsystem |
- Modellnummer: 56176
- UPC: 810101173783
- Marke: dotMod
- Ursprungsland: Deutschland
Lieferumfang
- 1x DotMod Switch R Pod 3ml Replacement Pods (2-Pack, chosen resistance)
Garantie und Support
For warranty information and customer support, please refer to the official dotMod webBesuchen Sie unsere Website oder wenden Sie sich an Ihren autorisierten Händler. Bewahren Sie Ihren Kaufbeleg für eventuelle Garantieansprüche auf.
Weitere Unterstützung finden Sie unter dotMod brand page on Amazon.