MMUNNA XH-W3005 Digital Humidity Controller User Manual

1. Einleitung

The MMUNNA XH-W3005 is a digital humidity controller designed to precisely monitor and regulate humidity levels within a specified range. It features a clear digital display, easy-to-use controls, and a high-accuracy humidity sensor, making it suitable for various applications requiring humidity management.

2. Sicherheitshinweise

• Stellen Sie sicher, dass die Stromversorgungslautstärketage entspricht der angegebenen Lautstärke des Controllerstage (AC 110-220V for this model). Incorrect voltage kann das Gerät beschädigen und ein Sicherheitsrisiko darstellen.
• All wiring should be performed by a qualified individual or with extreme caution, following local electrical codes.
• Do not expose the controller or sensor to water or excessive moisture, as this can lead to electrical shock or device malfunction.
• Vor jeglichen Verkabelungs- oder Wartungsarbeiten die Stromzufuhr unterbrechen.
• Halten Sie das Gerät von brennbaren Materialien fern.

3. Packungsinhalt

• 1 x Digital Humidity Controller (XH-W3005)
• 1 x Feuchtigkeitssensor

4. Spezifikationen

5. Produktüberschreitungview

The XH-W3005 humidity controller consists of a main control unit with a digital display and control buttons, and an external humidity sensor for accurate readings.

Abbildung 5.1: Gesamt view of the XH-W3005 Digital Humidity Controller with its connected sensor. The main unit features a digital display and control buttons, while the external sensor provides humidity readings.

Abbildung 5.2: Front panel of the XH-W3005 controller, highlighting the digital display for current humidity, the power indicator light, and the 'Up' and 'Down' buttons for humidity regulation settings.

Abbildung 5.3: Hinteren view of the XH-W3005 controller, showing the input and output wiring terminals and basic specifications printed on the casing.

6. Einrichtung und Installation

Proper wiring is crucial for the safe and correct operation of the humidity controller. Refer to the wiring diagram below and ensure all connections are secure.

Abbildung 6.1: Wiring diagram for the XH-W3005 Digital Humidity Controller. It illustrates connections for the 110-220V AC power supply, the humidity sensor, and the humidifier (load) output.

Verkabelungsanleitungen:

1. Stromversorgungsanschluss: Connect the AC 110-220V power supply to the designated input terminals (typically marked for power input). Ensure correct polarity if applicable, though for AC, live and neutral can be interchanged.
2. Humidity Sensor Connection: Plug the humidity sensor into its dedicated port on the controller. The sensor cable is usually pre-wired.
3. Lastanschluss: Connect the device you wish to control (e.g., a humidifier or dehumidifier) to the output terminals of the controller. The controller acts as a switch, turning the load on or off based on the humidity settings.
4. Überprüfen Sie die Verbindungen: Double-check all wiring for tightness and correctness before applying power.

7. Bedienungsanleitung

Once powered on, the controller will display the current humidity reading from the sensor.

7.1. Setting the Start Humidity

1. Drücken Sie die UP button once. The display will show the current 'start humidity' value.
2. Drücken Sie lange die UP button for approximately 3 seconds until the 'start humidity' value on the display begins to flash.
3. Verwenden Sie die UP or RUNTER Tasten zur Einstellung des gewünschten Startwerts der Luftfeuchtigkeit.
4. The setting will automatically save after a few seconds of inactivity, or you can short press any button to confirm.

7.2. Setting the Stop Humidity

1. Drücken Sie die RUNTER button once. The display will show the current 'stop humidity' value.
2. Drücken Sie lange die RUNTER button for approximately 3 seconds until the 'stop humidity' value on the display begins to flash.
3. Verwenden Sie die UP or RUNTER Tasten zum Einstellen des gewünschten Stopp-Feuchtigkeitswertes.
4. The setting will automatically save after a few seconds of inactivity, or you can short press any button to confirm.

Notiz: If the 'start humidity' is set higher than the 'stop humidity', the controller will operate in dehumidification mode. If 'start humidity' is lower than 'stop humidity', it will operate in humidification mode.

7.3. Wiederherstellen der Werkseinstellungen

To restore the controller to its default factory settings:

• Halten Sie die beiden UP Und RUNTER Tasten gleichzeitig.
• The display will show "888" briefly, indicating that the settings have been reset.
• The controller will then automatically detect and display the current humidity.

8. Fehlerbehebung

• Kein Display/Stromanschluss: Überprüfen Sie den Stromanschluss und stellen Sie sicher, dass die Spannungtage matches the controller's requirements. Verify the power source is active.
• Incorrect Humidity Reading: Ensure the humidity sensor is properly connected and not damaged. Avoid placing the sensor in direct contact with water or in areas with extreme temperature fluctuations.
• Load Not Activating: Verify the load device is functioning correctly and its wiring to the controller's output terminals is secure. Check your start and stop humidity settings.
• Fehlfunktion des Controllers: Try restoring factory settings as described in Section 7.3. If issues persist, contact customer support.

9. Wartung

• Keep the controller and sensor clean and free from dust and debris. Use a soft, dry cloth for cleaning.
• Avoid exposing the device to corrosive substances or extreme temperatures.
• Sorgen Sie für ausreichende Belüftung rund um den Controller, um eine Überhitzung zu vermeiden.

10. Garantie und Support

Informationen zur Garantie und zum technischen Support finden Sie in der Ihnen beim Kauf ausgehändigten Dokumentation oder wenden Sie sich an Ihren Händler. Bewahren Sie Ihren Kaufbeleg als Kaufnachweis auf.