ZLL Beast SG116 MAX Brushless 1/16 Scale 4WD RC Truck Instruction Manual

Einführung

This manual provides essential instructions for the safe and effective operation, maintenance, and setup of your ZLL Beast SG116 MAX Brushless 1/16 Scale 4WD RC Truck. Please read this manual thoroughly before first use and retain it for future reference.

Image: The ZLL Beast SG116 MAX RC Truck with its remote control, battery, charger, and tools.

Sicherheitshinweise

WARNING: Not suitable for children under 3 years due to small parts.

• Fahren Sie den RC-Truck immer auf offenen Flächen, fernab von Menschen, Haustieren und Hindernissen.
• Vermeiden Sie den Betrieb in der Nähe von öffentlichen Straßen, Gewässern oder Stromleitungen.
• Ensure the battery is fully charged and securely installed before operation.
• Berühren Sie während des Betriebs keine beweglichen Teile, um Verletzungen zu vermeiden.
• Schalten Sie den RC-Truck und die Fernbedienung immer aus, wenn sie nicht benutzt werden.
• Store the RC truck and accessories in a cool, dry place.

Lieferumfang

Überprüfen Sie nach dem Auspacken, ob alle unten aufgeführten Komponenten vorhanden sind:

• SG116MAX TRUCK
• Charging Cable and 7.4V Li-Ion Battery
• Screwdriver and Tool Set
• Produkthandbuch
• Fernbedienung

Installationshandbuch

1. Einbau und Aufladen der Batterie

1. Suchen Sie das Batteriefach an der Unterseite des RC-Trucks.
2. Carefully open the compartment and insert the provided 7.4V Li-Ion battery, ensuring correct polarity.
3. Verschließen Sie das Batteriefach fest.
4. To charge the battery, connect the charging cable to the battery and a compatible USB power source. The charging indicator will show the charging status.
5. Allow approximately 1 hour and 30 minutes for a full charge.

2. Vorbereitung der Fernbedienung

1. Install 3x AA batteries (not included) into the remote control's battery compartment.
2. Schalten Sie die Fernbedienung mit dem Netzschalter ein.
3. Turn on the RC truck. The remote control and truck should automatically pair. If not, refer to the troubleshooting section.

Bild: Detailliert view of the 2.4GHz remote control for the SG116 MAX.

Image: The remote control highlighting the three-speed regulation switch.

3. Wheelie Bar Attachment (Optional)

The wheelie bar can be attached to the rear of the truck to prevent it from flipping over during high-speed acceleration. Ensure the mounting points are aligned and secure the bar with the provided screws. Note that the mounting points may rotate, requiring careful alignment during installation.

Bedienungsanleitung

1. Grundlegende Steuerelemente

• Lenkrad: Turn left or right to control the direction of the truck.
• Gas Pedal (Trigger): Pull to accelerate forward, push to brake or reverse. The truck features full proportional steering and throttle for precise control.
• Geschwindigkeitsmodi: Use the switch on the remote to select between Low, Medium, and High speed modes. This allows adjustment for different skill levels and terrains.
• Scheinwerfer: The truck is equipped with headlights for visibility. Refer to the remote control diagram for the light switch.

2. Fahrtipps

• Start in Low speed mode to familiarize yourself with the controls.
• The 4WD system and all-terrain non-slip vacuum tires provide excellent traction on various surfaces including mud, snow, sand, grass, and rough trails.
• The powerful 4000kv 2847 brushless motor allows for speeds up to 60km/h with the included 7.4v Li-ion battery. With a 2S or 3S Lipo battery (not included), speeds can exceed 80km/h.
• Be mindful of battery heat when using 3S batteries, as this can stress the ESC.
• The active use time is approximately 25-30 minutes, depending on the selected speed mode.

Image: The ZLL Beast SG116 MAX demonstrating its off-road capability on gravel.

3. Offizielles Produktvideo

Wartung

1. Allgemeine Pflege

• After each use, clean the truck to remove dirt, dust, and debris. A soft brush or cloth can be used.
• The intelligent waterproof ESC provides protection against water splashes, but avoid submerging the vehicle.
• Regularly inspect the tires for wear and tear.

2. Bauteilprüfung

• Check for any loose screws or connections and tighten them as necessary.
• Inspect the metal differentials, CVD drive shafts, and spring shock absorbers for any damage. These metal upgrades contribute to the truck's durability.
• The high-strength front bumper and rear swing arm are designed to protect against collisions, but inspect them for cracks or damage after impacts.

Abbildung: Unterseite view of the RC truck, highlighting the chassis and drivetrain components.

Image: Close-up of the metal differential, a key durable component.

Image: The spring-loaded shock absorbers providing suspension for rough terrain.

Fehlerbehebung

Technische Daten

Garantie und Support

For warranty information, technical support, or replacement parts, please refer to the contact details provided with your purchase documentation or visit the official ZLL webBewahren Sie Ihren Kaufbeleg für Garantieansprüche auf.