OWON DGE1030/DGE1060 Arbitrary Waveform Generator User Manual

1. Einleitung

The OWON DGE1030 and DGE1060 are high-performance single-channel arbitrary waveform generators designed for a wide range of applications in electronics testing, education, and research. These devices offer precise waveform generation with a 3.6-inch TFT LCD for intuitive operation and comprehensive functionality.

Zu den Hauptmerkmalen gehören:

• Frequency output up to 30MHz (DGE1030) or 60MHz (DGE1060)
• Max 300MSa/s sample rate and 1μHz vertical resolution
• 14-bit vertical resolution and 8K arbitrary waveform length
• 5 basic waveforms and 160 built-in arbitrary waveforms
• Comprehensive modulation functions: AM, FM, PM, FSK, Sweep, and Burst
• SCPI and LabVIEW support for remote control
• Compact and ultra-thin body design

2. Packungsinhalt

Bitte überprüfen Sie nach Erhalt den Inhalt des Pakets, um sicherzustellen, dass alle Artikel vorhanden und unbeschädigt sind:

• 1x Host Machine (DGE1030 or DGE1060)
• 1x BNC to Alligator Clip Cable
• 1x USB-Kabel
• 1x USB to DC Cord
• 1x Netzteil
• 1x Kurzanleitung
• 1x Benutzerhandbuch (dieses Dokument)

Abbildung 2.1: Mitgeliefertes Zubehör und Hauptgerät.

3. Einrichtung

3.1 Stromanschluss

1. Connect the provided Power Adapter to the DC 5V power socket on the rear panel of the waveform generator.
2. Plug the power adapter into a suitable power outlet (100V-240V, 50/60Hz).
3. Press the ON/OFF button on the front panel to power on the device.

Figure 3.1: Rear panel with Power Socket and USB Device interface.

3.2 Ausgangsverbindung

Connect the BNC to Alligator Clip cable to the 'Out1' BNC connector on the front panel. Connect the alligator clips to your test circuit or device under test.

Figure 3.2: Front panel layout with 'Out1' channel output control area.

3.3-Zoll-PC-Anschluss (optional)

To use PC remote control via SCPI commands or LabVIEW, connect the waveform generator to your computer using the provided USB Cable. The USB Device interface is located on the rear panel.

Figure 3.3: Device connected to a PC for remote control.

4. Bedienungsanleitung

4.1 Benutzeroberfläche vorbeiview

The DGE1000 series features a 3.6-inch TFT color LCD display. All channel output waveform status and menu settings are fully displayed on the screen. Convenient shortcut keys improve man-machine interaction and working efficiency.

Figure 4.1: Front panel layout: 3.6-inch TFT LCD, function setting area, ON/OFF button, channel output control area, waveform switching area.

4.2 Grundlegende Wellenformerzeugung

The device supports 5 basic waveforms: Sine, Square, Pulse, Ramp, and Noise. To select a basic waveform:

1. Press one of the dedicated waveform buttons in the waveform switching area (e.g., Sine, Square, Ramp, Puls).
2. Use the rotary knob and navigation buttons to adjust parameters such as Frequency, Amplitude, Offset, and Phase.

Figure 4.2: LCD display showing Sine wave settings with high frequency stable output.

4.3 Erzeugung beliebiger Wellenformen

The DGE1000 series includes 160 built-in arbitrary waveforms. You can also store up to 16 non-volatile digital arbitrary waveforms.

1. Press the 'Arb' button.
2. Navigate through the list of built-in waveforms or select a stored user waveform.
3. Passen Sie die Parameter nach Bedarf an.

Figure 4.3: Arbitrary waveform selection menu and modulation mode options.

4.4 Modulationsfunktionen

The device supports various modulation types:

• BIN (AmpAmplitudenmodulation): Modulates the amplitude of the carrier wave.
• FM (Frequency Modulation): Modulates the frequency of the carrier wave.
• PM (Phase Modulation): Modulates the phase of the carrier wave.
• FSK (Frequency Shift Keying): Shifts the carrier frequency between two preset values.
• Fegen: Generates a waveform whose frequency changes continuously over a specified range and time.
• Platzen: Generates a specific number of waveform cycles (N-Cycle) or continuous cycles (Infinite) triggered internally or externally.

To access modulation functions, press the 'Mode' button and select the desired modulation type from the menu. Use the rotary knob and soft keys to configure modulation parameters.

Figure 4.4: LCD display showing Sweep function settings.

Figure 4.5: LCD display showing Burst function settings and arbitrary waveform file Management.

5. Wartung

5.1 Allgemeine Pflege

• Halten Sie das Gerät sauber und trocken. Vermeiden Sie den Kontakt mit Staub, Feuchtigkeit und extremen Temperaturen.
• Do not operate the device in environments with strong electromagnetic interference.
• Behandeln Sie das Gerät vorsichtig, um physische Schäden zu vermeiden.

5.2 Reinigung

To clean the exterior of the device, use a soft, damp Tuch. Verwenden Sie keine Scheuermittel oder Lösungsmittel, da diese das Material beschädigen können.asing oder Display. Stellen Sie vor der Reinigung sicher, dass das Gerät ausgeschaltet und von der Stromversorgung getrennt ist.

6. Fehlerbehebung

If you encounter issues with your OWON DGE1030/DGE1060, please refer to the following common troubleshooting steps:

• Kein Strom: Ensure the power adapter is correctly connected to the device and a working power outlet. Check the power adapter for any visible damage.
• Kein Ausgangssignal: Verify that the output cable is securely connected to the 'Out1' port and your test circuit. Check the output settings on the device's display (e.g., amplitude, frequency, ON/OFF state of the channel).
• Falsche Wellenform: Double-check the selected waveform type and its parameters (frequency, amplitude, offset, modulation settings).
• PC-Verbindungsprobleme: Ensure the USB cable is properly connected to both the device and the computer. Install any necessary drivers for SCPI or LabVIEW Kommunikation.

Sollte das Problem nach Durchführung dieser Schritte weiterhin bestehen, wenden Sie sich bitte an den Kundendienst, um weitere Unterstützung zu erhalten.

7. Spezifikationen

The following table details the technical specifications for the OWON DGE1030 and DGE1060 models:

Figure 7.1: Detailed Product Specifications for DGE1030 and DGE1060.

Allgemeine Spezifikationen:

• Anzeige: 3.6-Zoll-TFT-LCD mit einer Auflösung von 480 x 272
• Kommunikationsschnittstelle: USB-Gerät
• Abmessungen (B × H × T): 200 mm x 68.5 mm x 73.6 mm
• Weight (without package): 0.5 kg
• Stromversorgung: DC 5V (via Power Adapter)
• Maximale Leistung: 35 W
• Betriebslautstärketage Reichweite: 100V - 240V, 50/60Hz
• Zertifizierung: CE
• Batterie im Lieferumfang enthalten: NEIN
• Besonders bedenkliche Chemikalie: Keiner

Figure 7.2: Burst function parameters and Input/Output specifications.

8. Garantie und Support

This product comes with a 12-month warranty from the date of purchase. For any technical assistance, warranty claims, or support inquiries, please contact your vendor or OWON customer service directly. Ensure you retain your proof of purchase for warranty validation.

9. Benutzertipps

Aus den bereitgestellten Informationen waren keine spezifischen Benutzertipps verfügbar.views or Q&A. For optimal performance, always refer to the detailed operating instructions and ensure proper connections are made before powering on the device.