Einführung
This manual provides detailed instructions for the KEBIDUMEI 433Mhz Universal Copy Remote Control. This device is designed to duplicate existing 433Mhz remote control signals for various applications such as garage doors, electric gates, automated curtains, and lighting systems. Please read these instructions carefully before use to ensure proper operation and cloning.
Setup and Cloning
Before cloning, ensure your original remote control operates on the 433Mhz frequency. This copy remote control is compatible with a wide range of chips, including 2260, 2262, PT2264, 5326, SC5262, HT600, HT680, HT6207, HT6010, HT6012, HT6014, SMC918 series, 527, 1527, 2240, HCS101, HCS200/HCS201 (part code), HCS300/HCS301, and some single-chip microcomputers.
1. Code Clearing Method
- Press and hold the unlock button and the lock button simultaneously. (Note: On some remote shells, these might be the 'up' and 'down' buttons).
- The LED indicator light will flash three times.
- While still holding one button, release the other button.
- Press the released button three times. The LED indicator will then enter a fast flashing status.
- At this point, all memory data is cleared. The remote control will not show a lighting LED indicator when any button is pressed, confirming successful clearing.
2. Code Copying Method
- Hold your original remote control in one hand and the copy remote control in the other.
- Place the two remote controls as closely as possible. The ideal situation is to place them side-by-side on a flat surface with zero distance between them.
- Simultaneously press down the desired button on both the original and the copy remote control.
- When the LED indicator light on the copy remote flashes quickly after three initial flashes, the copy is successful for that button.
- Repeat this process for all other buttons you wish to copy.
Tipp: If the original remote control has a smaller transmitting power, place the original remote control directly against the back of the copy remote control for better signal reception during cloning. Avoid operating in areas with significant signal interference.
3. Code Recovery Method
If you accidentally clear the code or wish to restore a previously cloned code:
- Press and hold the 'C' and 'D' buttons (or equivalent buttons on your remote) on the copy remote control simultaneously.
- Continue holding until the indicator light flashes quickly. This will restore the remote control code that was previously stored.
Betrieb
Once successfully cloned, your KEBIDUMEI remote control will function identically to the original remote. The buttons typically correspond to various functions:
- Sperrtaste: Activates the lock function.
- Entsperrtaste: Deactivates the lock function.
- Stummschaltfläche: Mutes an alarm or similar function.
- Alarm/Panic Button: Activates an alarm or panic function.
- Tasten A, B, C, D: These are typically used for various functions depending on the original remote, such as opening/closing different garage doors, controlling lights, or other smart home devices.
The remote control offers a strong 433Mhz RF signal, providing a reliable and effective control distance of up to 50 meters in open areas. The wireless RF signal can also pass through walls, floors, and doors, though range may be reduced.
Wartung
Batteriewechsel
The remote control is powered by a 27A 12V battery, which is included. When the remote's range decreases significantly or the LED indicator becomes dim, it's time to replace the battery. To replace:
- Öffnen Sie vorsichtig die Fernbedienung casing.
- Die alte 27A 12V Batterie entfernen.
- Setzen Sie eine neue 27A 12V-Batterie ein und achten Sie dabei auf die richtige Polarität.
- Schließen Sie die Fernbedienung casing sicher.
Allgemeine Pflege
- Halten Sie die Fernbedienung trocken. Feuchtigkeit kann die internen Schaltkreise beschädigen.
- Vermeiden Sie extreme Temperaturen.
- Die Fernbedienung darf nicht fallen gelassen oder starken Stößen ausgesetzt werden.
- Reinigen Sie die Fernbedienung mit einem weichen, trockenen Tuch. Verwenden Sie keine scharfen Chemikalien oder Lösungsmittel.
Fehlerbehebung
| Problem | Mögliche Ursache | Lösung |
|---|---|---|
| Remote not working after cloning. | Cloning was unsuccessful or incomplete. | Clear the code (see Setup section) and attempt the cloning process again, ensuring the remotes are very close. |
| Remote has reduced operating range. | Low battery or signal interference. | Replace the 27A 12V battery. Try operating the remote in a different location to rule out interference. |
| LED-Anzeige leuchtet nicht. | Battery is dead or code has been cleared. | Replace the battery. If the code was intentionally cleared, proceed with cloning. |
| Cannot clone certain original remotes. | Original remote has a weaker signal or incompatible chip. | Ensure the original remote is placed directly against the copy remote. Verify the original remote's chip type is listed as compatible. |
Technische Daten
| Besonderheit | Detail |
|---|---|
| Markenname | kebidumei |
| Modellnummer | 433Mhz universal remote control |
| Frequenz | 433 MHz |
| Kanal | 4 |
| Drahtlose Kommunikation | RF |
| Verwenden | Universal, Lighting, Electric Door, Automated curtains, Switch |
| Batterie | 27A 12V Batterie (im Lieferumfang enthalten) |
| Übertragungsentfernung | More than 50 meters (open space) |
| Zertifizierung | CE |
| Farbe | Schwarz |
| Abmessungen (L x B x H) | 65 x 35 x 10 mm |
| Gewicht | 0.06 kg |
Benutzertipps
- Optimal Cloning: For best results during cloning, ensure the original remote and the copy remote are in direct contact or as close as possible. Some original remotes have weaker signals that require very close proximity.
- Interferenz: If you experience difficulty cloning or reduced range, try performing the cloning process or operating the remote in an area free from strong radio frequency interference.
- Akkulaufzeit: Keep a spare 27A 12V battery on hand. A common reason for decreased performance is a low battery.
Garantie und Support
For any issues, questions, or technical support regarding your KEBIDUMEI 433Mhz Universal Copy Remote Control, please contact the seller or manufacturer directly. Please refer to your purchase documentation for specific warranty terms and contact information.
