Einführung
The Bora Portamate PM-7002 Quick-Mount Tool Attachments are designed to facilitate the rapid attachment and detachment of various power tools and machines to compatible Portamate miter saw stands and work centers. These mounts enhance the versatility of your workspace by allowing quick tool changes without the need to repeatedly set up mounting hardware.
Each set includes two 20-inch long tool mounts. Once attached to your power tools, these mounts can remain in place, ensuring stability and readiness for use with your Portamate stand.
Produkteigenschaften
- Enables quick attachment and detachment of power tools to Portamate stands.
- Compatible with a wide range of power tools including miter saws, routers, band saws, and scroll saws.
- Designed to work with all Bora Portamate miter saw stands (excluding PM-8000 Portacube).
- Each set contains two tool mounts.
- Mounts are 20 inches (approximately 50.8 cm) in length.
Kompatibilität
The PM-7002 Tool Mounts are designed for use with the following Portamate Miter Saw Stands and Work Centers:
- PM-3600
- PM-3900
- PM-4000
- PM-4400
- PM-5000
- PM-6000
- PM-6300
- PM-7000
Notiz: These mounts are not compatible with the PM-8000 Portacube.
Setup und Installation
Follow these steps to properly attach the PM-7002 Tool Mounts to your power tool and then to a compatible Portamate stand.
Attaching Mounts to Your Power Tool
- Bereiten Sie das Werkzeug vor: Ensure your power tool is unplugged and stable on a workbench. Identify the mounting holes on the base of your tool.
- Position Mounts: Place one PM-7002 tool mount on each side of your power tool's base, aligning the slots or holes on the mounts with the mounting holes on your tool.
- Sichere Halterungen: Use appropriate bolts, washers, and nuts (typically supplied with your power tool or the Portamate mounts) to securely fasten the mounts to the tool. Ensure all fasteners are tightened firmly to prevent any movement during operation.
- Stabilität prüfen: Gently shake the tool to confirm the mounts are securely attached and there is no wobble.
Attaching Tool to Portamate Stand
- Positionswerkzeug: Carefully lift your power tool with the attached PM-7002 mounts and align the mounts with the rails of your Portamate miter saw stand.
- Verriegelungsmechanismus aktivieren: Slide the tool mounts onto the stand's rails until they click into place or the locking levers can be engaged. Ensure both mounts are fully seated and locked onto the stand.
- Sicherheit überprüfen: Before operating, gently push and pull on the tool to confirm it is firmly locked onto the stand and cannot accidentally dislodge.
Bedienungsanleitung
The PM-7002 mounts are designed for quick tool changes. Once your power tool is secured to the mounts, and the mounts are attached to your Portamate stand, you can begin operation.
To Detach a Tool:
- Sicherheit gewährleisten: Unplug the power tool and ensure all moving parts have come to a complete stop.
- Entriegelungssperren: Locate the quick-release levers or mechanisms on both PM-7002 mounts. Engage these mechanisms to unlock the mounts from the stand's rails.
- Lift Tool: Carefully lift the power tool straight up from the stand.
To Attach a Different Tool:
Repeat the "Attaching Tool to Portamate Stand" steps from the Setup section for any other power tool equipped with PM-7002 mounts.
Wartung
Regular maintenance ensures the longevity and safe operation of your PM-7002 Tool Mounts.
- Reinigung: Periodically wipe down the mounts to remove sawdust, debris, and grime. A damp cloth is usually sufficient. Avoid harsh chemicals that may damage the finish or plastic components.
- Befestigungselemente prüfen: Regularly check all bolts, nuts, and screws that secure the mounts to your power tool. Tighten any loose fasteners to maintain stability.
- Verriegelungsmechanismen prüfen: Ensure the quick-release levers and clamping components operate smoothly and engage securely. If any part appears worn or damaged, consider replacement.
- Lagerung: When not in use, store the mounts (either attached to tools or separately) in a clean, dry environment to prevent rust or damage.
Fehlerbehebung
If you encounter issues with your PM-7002 Tool Mounts, consider the following:
- Tool Wobbles on Stand:
- Ensure the quick-release levers are fully engaged and locked.
- Verify that the mounts are securely fastened to the power tool's base. Tighten all bolts.
- Check if the Portamate stand's rails are clean and free of obstructions.
- Schwierigkeiten beim Anbringen/Abnehmen:
- Ensure the quick-release levers are fully disengaged when detaching.
- Check for any debris or damage on the mounts or stand rails that might impede smooth operation.
- Confirm the tool is aligned correctly with the stand rails before attempting to slide it on.
- Mounts do not fit stand:
- Verify that your stand is a compatible Portamate model (refer to the Compatibility section). These mounts are not universal for all brands or models.
Technische Daten
| Modellnummer | PM-7002 |
| Hersteller | Affinity Tool Works |
| Technische Daten | Ungefähr 55.88 x 22.86 x 15.24 cm (22 x 9 x 6 Zoll) |
| Artikelgewicht | Ungefähr 2.04 kg (4.5 lbs) |
| Artikelpaket Menge | 1 (set of 2 mounts) |
| Montagelänge | 20 Zoll (ca. 50.8 cm) |
| Stromquelle | Crank (manual operation) |
| Verwendung | Professional |
Garantieinformationen
The Bora Portamate PM-7002 Tool Mounts come with a 1 Jahr eingeschränkte Garantie from the date of purchase. This warranty covers defects in materials and workmanship under normal use. For specific terms and conditions, or to make a warranty claim, please contact Affinity Tool Works customer support.
Support und Kontakt
For further assistance, technical support, or inquiries regarding your Bora Portamate PM-7002 Tool Mounts, please contact the manufacturer:
Hersteller: Affinity Tool Works
Please refer to the official BORA or Affinity Tool Works webAuf dieser Website finden Sie die aktuellsten Kontaktinformationen, einschließlich Telefonnummern und E-Mail-Adressen.
You can visit the BORA Store on Amazon for more products and information: BORA Store
