Produkt überview
The Viper 474V is a 4-button remote control designed for use with compatible Viper vehicle security and remote start systems. This remote allows for convenient control of your vehicle's security features, including locking, unlocking, auxiliary functions, and remote start/panic.
Image: Viper 474V 4-Button Remote. This image displays the front of the remote control, featuring four distinct buttons: a lock icon, an unlock icon, an 'AUX' button, and an orange button with a speaker/horn icon. The Viper logo is visible below the buttons, and a metal key ring is attached at the bottom.
Einrichtung und Programmierung
To program your Viper 474V remote to your vehicle's security system, follow these steps. Ensure you have located your system's valet switch, typically found under the driver's lower dash or on the driver's side kick panel. The exact procedure may vary slightly depending on whether your Viper system includes a remote start module.
- Fahrzeug vorbereiten: Open the driver's side door.
- Zündung an: Insert the key into the ignition and turn it to the "Run" position. Do not start the engine. All dashboard warning lights should illuminate.
- Zugang zum Programmiermodus:
- With Remote Start Module: Press and release the valet button once. This selects Channel 1.
- Without Remote Start Module: Press and release the valet button seven (7) times. This selects Channel 7.
- Confirm Channel Selection: Press the valet button once more and hold it down. The alarm LED on the dash will flash the same number of times as the selected channel (1 or 7), and the siren (if connected) will chirp to confirm. Continue holding the valet button.
- Fernbedienung programmieren: While still holding the valet button, press the "Lock" button on your new Viper 474V remote. Hold the "Lock" button until the siren sounds, indicating successful programming.
- Programmiermodus verlassen: Release the "Lock" button on the remote, then release the valet button. Turn the ignition key to the "Off" position and remove it from the vehicle. Close the driver's door.
- Testen Sie die Fernbedienung: Test the new remote by attempting to lock and unlock the vehicle.
Note: If you wish to erase all previously programmed remotes and program only the new one, consult your system's specific installation manual for the master reset procedure, which typically involves a different valet button sequence.
Bedienungsanleitung
The Viper 474V remote features four buttons for controlling your vehicle's security system:
- Sperrknopf (🔒): Drücken Sie diese Taste, um das Sicherheitssystem zu aktivieren und die Fahrzeugtüren zu verriegeln.
- Entsperrknopf (🔓): Drücken Sie diese Taste, um das Sicherheitssystem zu deaktivieren und die Fahrzeugtüren zu entriegeln.
- AUX-Taste: This button controls an auxiliary function, which can be programmed for various purposes such as trunk release, power windows, or other accessories. Refer to your system's installation manual for the specific function assigned to this button.
- Orange Button (Speaker/Horn Icon): This button typically activates the remote start function (if installed and programmed) or the panic alarm.
- Ferngesteuerter Start: Press twice to activate remote engine start.
- Panik: Press and hold for a few seconds to activate the panic alarm. Press again to deactivate.
Note: Button sensitivity is high. Be mindful when carrying the remote in pockets to avoid unintentional activation of functions like remote start or panic.
Wartung
Batteriewechsel
The Viper 474V remote is powered by a small battery. If the remote's range decreases significantly or it stops responding, the battery may need replacement. To replace the battery:
- Öffnen Sie vorsichtig die Fernbedienung casing. This usually involves prying it open along the seam with a small, flat tool.
- Note the type and orientation of the existing battery.
- Remove the old battery and insert a new one of the same type, ensuring correct polarity.
- Schließen Sie die Fernbedienung.asing sicher.
Alte Batterien müssen stets gemäß den örtlichen Vorschriften verantwortungsvoll entsorgt werden.
Fehlerbehebung
- Fernbedienung reagiert nicht:
- Überprüfen Sie die Batterie. Tauschen Sie sie gegebenenfalls aus.
- Ensure the remote is within range of the vehicle's receiver.
- Re-attempt the programming steps outlined in the "Setup and Programming" section.
- Verify that the valet switch is functioning correctly.
- Unintentional Activations:
- The buttons on the 474V remote are sensitive. Avoid placing the remote in tight pockets or areas where buttons might be accidentally pressed.
- Begrenzte Reichweite:
- Ersetzen Sie die Batterie der Fernbedienung.
- Ensure there are no large metallic objects or electronic devices interfering with the signal between the remote and the vehicle.
Technische Daten
- Modellnummer: 474 V
- Marke: VIPER
- Produktabmessungen: 8 x 6 x 1.75 Zoll
- Artikelgewicht: 2.4 Unzen
- Konnektivitätstechnologie: Infrarot
- Besonderheit: Ergonomisches Design
- Kompatible Geräte: Vehicle Alarm Systems
- Maximale Anzahl unterstützter Geräte: 1
Garantie und Support
For warranty information, technical support, or further assistance with your Viper 474V remote or associated vehicle security system, please refer to the documentation provided with your complete Viper system or contact Directed Electronics Inc., the manufacturer, directly. You can typically find support contact details on the manufacturer's official webWebsite.
It is recommended to register your product with the manufacturer, if applicable, to ensure you receive updates and support.
