Benutzerhandbücher+

Westek TMDCD60

Westek TMDCD60 Wandschalter-Zeitschaltuhr für den Innenbereich mit 6 Einstellungen und Countdown-Funktion – Benutzerhandbuch

Model: TMDCD60

Einführung

The Westek TMDCD60 is a hardwire indoor countdown timer designed to replace a standard wall switch. It provides timed control for lights, fans, heaters, and other devices, automatically turning them off after a selected duration. This manual provides instructions for safe installation, operation, and maintenance of your timer switch.

Sicherheitshinweise

WARNUNG: Stromschlaggefahr. Improper installation can lead to serious injury or death. Always turn off power at the circuit breaker or fuse box before beginning installation. Consult a qualified electrician if you are unsure about any part of the installation process.

Packungsinhalt

Produkt überview

The Westek TMDCD60 timer switch features a single push-button control and LED indicators for selected time settings. It is designed to fit into a standard wall switch box and can be used with a standard rocker wallplate (not included).

Front view of the Westek TMDCD60 timer switch, showing the push button and LED indicators for 10, 20, 30, 60 minutes, and HOLD.

Abbildung 1: Vorderseite view of the TMDCD60 timer switch. The face includes a single control button and five LED indicators labeled "10 MIN", "20 MIN", "30 MIN", "60 MIN", and "HOLD".

Installation

  1. Strom ausschalten: Locate the circuit breaker or fuse that controls the switch you are replacing. Turn off the power completely before proceeding. Verify power is off using a voltage Tester.
  2. Vorhandenen Switch entfernen: Carefully remove the wallplate and unscrew the existing switch from the wall box. Disconnect the wires from the old switch. Note the connections for reference.
  3. Drähte identifizieren: The Westek TMDCD60 timer requires four wires:
    • Schwarzes Kabel: Hot (Line)
    • Roter Draht: Load (to the device being controlled)
    • Weißer Draht: Neutral
    • Grüner Draht: Boden

    Ensure your wall box contains a neutral wire. If not, this timer cannot be installed without running a new neutral wire, which should be done by a qualified electrician.

    Zurück view of the Westek TMDCD60 timer switch, showing the wiring labels for Black (Hot), Red (Load), White (Neutral), and Green (Ground).

    Abbildung 2: Zurück view of the TMDCD60, illustrating the labeled wires for proper connection.

  4. Kabel anschließen: Using wire nuts (not included), connect the wires from the wall box to the corresponding wires on the TMDCD60 timer switch:
    • Verbinden Sie Schwarz wire from the timer to the Hot (Line) wire from the wall box.
    • Verbinden Sie Rot wire from the timer to the Laden wire from the wall box (to the light/fan).
    • Verbinden Sie Weiß wire from the timer to the Neutral wire from the wall box.
    • Verbinden Sie Grün wire from the timer to the Boden wire from the wall box.
  5. Zeitschaltuhr montieren: Carefully fold the wires into the wall box. The timer is deeper than a standard switch, so ensure there is enough space. Secure the timer switch to the wall box using the provided screws.
  6. Wandplatte installieren: Attach a standard rocker wallplate (not included) over the timer switch.
  7. Strom wiederherstellen: Schalten Sie den Strom am Sicherungsautomaten oder Sicherungskasten wieder ein.

Betrieb

The TMDCD60 timer operates with a single push-button control. Each press cycles through the available countdown settings and the HOLD function.

  1. Turning On and Setting Timer: Press the control button once to activate the timer. The timer will cycle through the following settings with each subsequent press:
    • OFF (no LED lit)
    • 10 Minutes (10 MIN LED lights up)
    • 20 Minutes (20 MIN LED lights up)
    • 30 Minutes (30 MIN LED lights up)
    • 60 Minutes (60 MIN LED lights up)
    • HOLD (HOLD LED lights up)

    The connected device will remain on for the selected duration and then automatically turn off. The corresponding LED will indicate the active setting.

  2. HOLD-Funktion: To keep the connected device on indefinitely, press and hold the control button for approximately one second until the "HOLD" LED illuminates. In HOLD mode, the device will remain on until you press the button again to turn it off or select a countdown setting.
  3. Ausschalten: To turn off the connected device before the countdown finishes or while in HOLD mode, press the control button until no LEDs are lit.

Wartung

The Westek TMDCD60 timer switch requires minimal maintenance. To clean the surface, wipe with a soft, damp Mit einem Tuch abwischen. Keine Scheuermittel oder Lösungsmittel verwenden. Vor der Reinigung sicherstellen, dass das Gerät ausgeschaltet ist.

Fehlerbehebung

ProblemMögliche UrsacheLösung
Timer does not turn on or operate.Der Schalter erhält keinen Strom.
Falsche Verkabelung.		Überprüfen Sie den Schutzschalter oder die Sicherung.
Verify all wiring connections are correct as per the Installation section. Ensure a neutral wire is connected.
Das angeschlossene Gerät schaltet sich nach der ausgewählten Zeit nicht aus.Timer is in HOLD mode.
Falsche Verkabelung.		Press the button to cycle out of HOLD mode.
Recheck load wire connection.
Die LED-Anzeigen funktionieren nicht.Der Schalter erhält keinen Strom.
Gerätestörung.		Stromversorgung prüfen.
If power is present and wiring is correct, the unit may be faulty. Contact customer support.

Technische Daten

Garantie und Support

This Westek product is covered by a 1 Jahr eingeschränkte Garantie ab Kaufdatum. Diese Garantie deckt Material- und Verarbeitungsfehler bei normalem Gebrauch ab.

For technical support or warranty claims, please contact Westek customer service. You can find more information and contact details on the official Westek webWebsite oder durch Besuch der Westek Store on Amazon.