1. Produktüberschreitungview
The Sicce Ultrazero Flat Sucking Pump is designed for efficient removal of water from various areas, including flooded cellars, garages, and other spaces where minimal residual water is desired. This submersible pump is capable of reducing water levels down to 2-3 mm.
Hauptmerkmale:
- Capable of pumping water down to 2 mm residual level.
- Fully submersible design.
- Handles dirt particles up to 3 mm in size.
- Equipped with a 10-meter power cable.
- Features a practical carry handle for easy transport.
Abbildung 1: Überview of the Sicce Ultrazero Flat Sucking Pump.
2. Sicherheitshinweise
Read all safety warnings and instructions before operating the pump. Failure to follow these instructions may result in electric shock, fire, or serious injury.
- Always disconnect the pump from the power supply before handling, cleaning, or performing any maintenance.
- Stellen Sie sicher, dass die Stromversorgungslautstärketage matches the pump's specifications (230 V/50 Hz).
- Do not operate the pump with a damaged power cord or plug. If damaged, it must be replaced by the manufacturer, service agent, or similarly qualified persons to avoid a hazard.
- Do not use the pump to handle flammable or explosive liquids.
- Halten Sie Kinder und Unbefugte vom Arbeitsbereich fern.
- Um eine Überhitzung zu vermeiden, muss die Pumpe während des Betriebs vollständig eingetaucht sein.
- Avoid running the pump dry for extended periods.
- This pump is designed for water only. Do not use it for other liquids without consulting the manufacturer.
3. Einrichtung und Installation
Follow these steps to properly set up your Ultrazero pump:
- Auspacken der Pumpe: Nehmen Sie die Pumpe und sämtliches Zubehör vorsichtig aus der Verpackung. Prüfen Sie sie auf Beschädigungen.
- Connect the Discharge Hose:
The pump features a 26.44 mm (3/4") AG pressure connection. Attach a suitable discharge hose (e.g., 20 mm (3/4") hose connection) to this outlet. Ensure the connection is secure to prevent leaks.
Figure 2: Close-up of the pump's discharge outlet and integrated carry handle.
- Positionieren Sie die Pumpe: Place the pump directly on the surface from which water needs to be removed. Ensure the pump is stable and upright. The flat base allows for efficient water removal down to minimal levels.
- Route the Discharge Hose: Direct the discharge hose to a suitable drainage area, ensuring the water will not flow back into the area being drained.
- Stromanschluss: Plug the 10-meter power cable into a grounded 230 V/50 Hz electrical outlet. Ensure the outlet is protected by a Ground Fault Circuit Interrupter (GFCI) for added safety, especially in wet environments.
Figure 3: The flat base of the pump designed for low residual water levels.
4. Bedienungsanleitung
The Ultrazero pump is designed for simple operation:
- Tauchen Sie die Pumpe ein: Ensure the pump is fully submerged in the water you wish to remove. The pump requires water to cool its motor and operate correctly.
- Pumpen beginnen: Once submerged and connected to power, the pump will begin operating automatically. It does not feature a float switch, so manual monitoring is required for optimal use.
- Wasserstand überwachen: The pump will continue to operate until the water level reaches its minimum suction capability of 2-3 mm.
- Pumpen stoppen: To stop the pump, disconnect it from the power supply. It is recommended to disconnect the pump once the desired water level is reached or if the pump starts to run dry.
Figure 4: The Ultrazero pump effectively draining water from a small pool.
Figure 5: The pump in action on a flooded floor, demonstrating its low-level suction capability.
Figure 6: Illustration of the pump's ability to reduce water levels to approximately 2 mm.
5. Wartung
Regelmäßige Wartung gewährleistet die Langlebigkeit und optimale Leistung Ihrer Pumpe.
- Reinigung: After each use, especially when pumping dirty water, rinse the pump thoroughly with clean water. This helps prevent sediment buildup.
- Auf Schmutz prüfen: Periodically check the pump's intake area for any debris (e.g., leaves, small stones) that might obstruct water flow. Remove any blockages carefully after disconnecting power.
- Kabelinspektion: Regularly inspect the power cable for cuts, abrasions, or other damage. Do not use the pump if the cable is damaged.
- Lagerung: When not in use, store the pump in a clean, dry place, protected from frost.
Figure 7: The pump can also be used for transferring water for tasks like garden watering from a rain barrel.
6. Fehlerbehebung
If you encounter issues with your Ultrazero pump, refer to the following common problems and solutions:
| Problem | Mögliche Ursache | Lösung |
|---|---|---|
| Pumpe startet nicht. | Keine Stromversorgung. Stromkabel beschädigt. Motorüberlastungsschutz aktiviert. | Überprüfen Sie den Stromanschluss und die Steckdose. Inspect cable for damage; replace if necessary (by qualified personnel). Disconnect power, allow motor to cool, then reconnect. |
| Die Pumpe läuft, aber es wird kein Wasser gefördert. | Intake blocked. Abflussschlauch geknickt oder verstopft. Airlock in pump. | Disconnect power, clear intake. Check and clear discharge hose. Briefly lift and lower the pump while submerged to release trapped air. |
| Verminderte Pumpenleistung. | Partial blockage. Impeller worn. | Disconnect power, clean pump intake and impeller area. Wenden Sie sich für Serviceleistungen an den Kundendienst. |
| Pumpe stoppt unerwartet. | Overheating due to low water level or blockage. Elektrischer Fehler. | Disconnect power, check water level and clear blockages. Allow to cool. Sollte das Problem weiterhin bestehen, wenden Sie sich bitte an den Kundendienst. |
If the problem persists after attempting these solutions, please contact Sicce customer support.
7. Technische Daten
Detailed specifications for the Sicce Ultrazero Flat Sucking Pump, Model 925607:
| Spezifikation | Wert |
|---|---|
| Marke | Sicce |
| Modellnummer | 925607 |
| Max. Delivery Rate (Flow Rate) | 3000 l/h |
| Max. Lieferhöhe | 3.1 m |
| Power Consumption (P1) | 80 Watt |
| Betriebslautstärketage | 220-240 V / 50 Hz |
| Conductor Length (Power Cable) | 10 m (three-core, indoor and outdoor use) |
| Druckanschluss | 26.44 mm (3/4") AG |
| Schlauchanschlussdurchmesser | 20 mm (3/4") |
| Max. Solids Size | 3 mm |
| Restwasserstand | Down to 2-3 mm |
| Produktabmessungen (ca.) | 140 mm (Diameter) x 160 mm (Height) / 5.5" x 6.3" |
| Artikelgewicht | 2.6 kg |
| Schwimmerschalter | NEIN |
| Überlastschutz | No (Internal thermal protection may exist, but no external reset) |
| Herkunft | Hergestellt in Italien |
Figure 8: Technical drawing illustrating the pump's dimensions and 3/4" GAS connection.
8. Garantie und Support
For warranty information or technical support regarding your Sicce Ultrazero Flat Sucking Pump, please contact Sicce customer service. Keep your purchase receipt and model number (925607) handy when contacting support.
Hersteller: Ebara
Marke: Sicce
For further assistance, visit the official Sicce webBesuchen Sie unsere Website oder wenden Sie sich an Ihren lokalen Händler.
