Einführung
This manual provides detailed instructions for the installation, operation, and maintenance of your Claber 90763 Timer Kit 20 Practico. This automatic drip irrigation system is designed for watering up to 20 potted plants on terraces or patios, ensuring efficient and consistent hydration.
Sicherheitshinweise
- Kein Frost: Do not expose the timer or system components to freezing temperatures.
- Nicht für Kinder geeignet: Bewahren Sie das Produkt außerhalb der Reichweite von Kindern auf.
- Nur für den Außenbereich: Dieses Produkt ist für die Installation im Freien konzipiert.
- Nicht eintauchen: The timer unit must not be placed underwater.
- Valve Box Installation: Do not install the timer inside a valve box.
- Wasserdruck: Ensure water pressure is between 0.5 bar (7.3 psi) and 10 bar (145 psi).
Packungsinhalt
Überprüfen Sie, ob alle Komponenten in Ihrem Set vorhanden sind:
Image: All components of the Claber 90763 Timer Kit 20 Practico, including the timer, main hose, drippers, stakes, and connectors.
- 1x Aquauno Pratico Timer
- 1x Pressure Stabilizer
- 1x 20m (1/4" - 4-6mm) Main Hose
- 20x Adjustable Drippers
- 20x Stakes for Drippers
- Various Connectors and Fittings (e.g., 3-way connectors, end caps)
Installationsanweisungen
1. Einlegen der Batterie
- Open the battery compartment on the back of the Aquauno Pratico timer.
- Insert one new 9V alkaline battery, ensuring correct polarity.
- Verschließen Sie das Batteriefach fest.
Image: A section from the instruction manual illustrating the steps for inserting a 9V battery into the timer.
Notiz: The timer requires a 9V alkaline battery (not included). If the battery is low, the timer's LED will flash. Replace the battery promptly to avoid interruption of watering cycles.
2. Timer and Pressure Stabilizer Installation
- Attach the pressure stabilizer to the outlet of the Aquauno Pratico timer.
- Screw the timer onto a standard 3/4" outdoor tap. Ensure a tight, leak-free connection.
- The timer should be installed vertically, with the display facing outwards for easy access.
Image: The Claber Aquauno Pratico timer connected to an outdoor water tap, with the pressure stabilizer attached below it.
3. Drip System Assembly
- Connect the main hose (1/4" or 4-6mm) to the outlet of the pressure stabilizer.
- Lay out the main hose to reach all potted plants you intend to water.
- At each plant location, cut the main hose and insert a 3-way connector or a direct dripper connection.
- Attach the adjustable drippers to the hose or connectors.
- Use the provided stakes to secure the drippers near the base of each plant.
- Cap the end of the main hose with an end cap to maintain pressure.
Image: An illustration of a balcony with potted plants being watered by the Claber drip irrigation system, showing hose routing and dripper placement.
Bedienungsanleitung
1. Programming the Aquauno Pratico Timer
The Aquauno Pratico timer allows for daily watering with a maximum duration of 60 minutes. Refer to the timer's interface for specific programming steps:
Bild: Eine detaillierte view of the Claber Aquauno Pratico timer, showing the control buttons and display area.
- Startknopf (grün): Press to initiate a watering cycle or confirm a setting.
- Stoppknopf (rot): Press to stop an ongoing watering cycle or cancel a setting.
- Programming Dial: Rotate the dial to select the desired watering duration (e.g., 5, 10, 15, 20, 30, 45, 60 minutes). The timer will automatically water daily for the selected duration.
- Reset/Cancel Button: Use to reset the timer or cancel current programming.
For detailed programming steps, refer to the specific instructions provided on the timer unit or the full manual available online.
2. Adjusting Drippers
Each dripper is adjustable to control the water flow to individual plants. Rotate the cap on each dripper to increase or decrease the water output. Adjust the flow based on the plant's water requirements and soil type.
Wartung
- Reinigung: Wipe the timer and components with a damp Bei Bedarf mit einem Tuch abwischen. Keine Scheuermittel verwenden.
- Filterreinigung: The timer includes a filter at the inlet. Periodically remove and clean this filter to prevent blockages and ensure proper water flow.
- Überwinterung: Before the first frost, disconnect the timer and drain all water from the system. Store the timer and components in a dry, frost-free location. Remove the battery before storage.
- Batteriewechsel: Replace the 9V alkaline battery annually or when the low battery indicator flashes.
Fehlerbehebung
| Problem | Mögliche Ursache | Lösung |
|---|---|---|
| Timer does not start watering. | Dead or low battery. Incorrect programming. Water tap is off. | Replace battery. Re-program the timer. Ensure water tap is fully open. |
| Kein Wasserdurchfluss aus den Tropfern. | Clogged filter. Kinked hose. Drippers are closed. Low water pressure. | Clean the inlet filter. Check hose for kinks. Open drippers. Ensure adequate water pressure. |
| Aus den Anschlüssen tritt Wasser aus. | Loose connections. Damaged O-rings/washers. | Tighten all connections. Inspect and replace any damaged O-rings or washers. |
| Inconsistent watering. | Uneven water pressure. Partially clogged drippers. | Ensure pressure stabilizer is correctly installed. Clean drippers. |
Technische Daten
- Marke: Claber
- Modell: 90763 (Timer Kit 20 Practico)
- Material: Plastik
- Product Dimensions (Timer): 2.36"T x 3.15"B x 4.33"H
- Item Weight (Timer): Ungefähr 0.037 Unzen (1.05 Gramm)
- Bewässerungshäufigkeit: Täglich
- Bewässerungsdauer: Up to 60 minutes (adjustable)
- Energiequelle: 1x 9V Alkaline Battery (not included)
- Wasserdruckbereich: 0.5 - 10 bar (7.3 - 145 psi)
- Pflegehinweise: Wischen mit Damp Tuch
Garantie und Support
For warranty information, technical support, or additional resources, please visit the official Claber webWebsite oder wenden Sie sich an den Kundendienst.
Online-Ressourcen: Claber Instruction Manuals
Hersteller: Claber
