JASCO GE Z-Wave Ein/Aus-Relais-Schalter (Modell 45609 / ZW4001) Bedienungsanleitung

1. Einleitung

This instruction manual provides comprehensive guidance for the installation, configuration, and operation of the JASCO GE Z-Wave On/Off Relay Switch, Model 45609 (ZW4001). This device is designed to integrate into your Z-Wave wireless lighting control system, enabling remote ON/OFF control of permanently installed lighting fixtures and ceiling fans.

The GE Z-Wave On/Off Relay Switch offers a convenient solution for smart home automation, compatible with various lighting types including CFL, LED, Xenon, Halogen, Fluorescent, and Incandescent. It supports both 2-way and 3-way wiring configurations when used with an auxiliary switch.

2. Wichtige Sicherheitshinweise

WARNUNG: STROMSCHLAGGEFAHR. Installation involves high voltage wiring. Improper installation can result in serious injury or death. Always consult a qualified electrician if you are unsure about any part of the installation process.

• STROMVERSORGUNG TRENNEN: Before installation, turn OFF the power to the switch location at the circuit breaker or fuse box.
• NEUTRAL WIRE REQUIRED: This switch requires a neutral wire for operation. If your existing switch box does not have a neutral wire, consult a qualified electrician.
• NUR INNEN BENUTZEN: Dieses Gerät ist für den Gebrauch in Innenräumen an trockenen Orten bestimmt.
• LOAD COMPATIBILITY: Ensure the connected load does not exceed the switch's maximum rating.
• LÜFTERSTEUERUNG: This switch provides ON/OFF control for ceiling fans; speed control is not supported.

3. Packungsinhalt

• GE Z-Wave On/Off Relay Switch (Model 45609 / ZW4001)
• Wiring Nuts (typically included, but may vary)
• Bedienungsanleitung (dieses Dokument)

Notiz: A wallplate is not included and must be purchased separately.

4. Einrichtung und Installation

Follow these steps carefully to install your GE Z-Wave On/Off Relay Switch. If you are unfamiliar with electrical wiring, please consult a qualified electrician.

4.1 Schaltplan (siehe oben)view

The switch requires Line (Hot), Load, Neutral, and Ground connections. For 3-way installations, an auxiliary switch (e.g., GE 45610) and a traveler wire are also required.

Abbildung 1: Front view of the GE Z-Wave On/Off Relay Switch (Model 45609) without a wallplate, showing the rocker switch and mounting bracket. The "TOP" indicator is visible at the top of the metal bracket. Electrical ratings (120VAC, 60Hz, 15A Resistive Load) are printed on the side.

4.2 Installationsschritte

1. Strom ausschalten: Locate the circuit breaker or fuse that supplies power to the switch box. Turn it OFF completely. Verify power is off using a voltage Tester.
2. Vorhandenen Switch entfernen: Carefully remove the wallplate and unscrew the existing switch from the wall box. Disconnect the wires from the old switch, noting which wire was connected to which terminal. It is recommended to label the wires (Line, Load, Neutral, Ground, Traveler if applicable).
3. Drähte identifizieren:
   • Line (Hot): Connects to the electrical panel, providing power.
   • Laden: Connects to the light fixture or fan.
   • Neutral: Typically white, required for the switch to operate.
   • Boden: Bare copper or green wire.
   • Traveler (for 3-way): Connects to the auxiliary switch.
4. Wire the Z-Wave Switch: Connect the wires to the GE Z-Wave switch terminals as follows:
   • Erdungskabel: Connect to the green GROUND terminal.
   • Neutralleiter: Connect to the white NEUTRAL terminal.
   • Außenleiter (stromführender Draht): Connect to the black LINE terminal.
   • Lastkabel: Connect to the black LOAD terminal.
   • Traveler Wire (if 3-way): Connect to the red TRAVELER terminal. Cap off the traveler wire if not used.
5. Montieren Sie den Schalter: Carefully fold the wires and push the switch into the wall box. Secure the switch with the provided screws.
6. Wandplatte installieren: Attach the new wallplate (not included) over the switch.
7. Strom wiederherstellen: Schalten Sie den Strom am Sicherungsautomaten wieder ein.
8. Testfunktionalität: Manually press the rocker switch to ensure the connected light or fan turns ON and OFF.

Abbildung 2: Front view of the GE Z-Wave On/Off Relay Switch (Model 45609) with a light almond wallplate installed. This illustrates the finished appearance of the switch in a standard electrical box.

5. Bedienungsanleitung

5.1 Manuelle Steuerung

The GE Z-Wave On/Off Relay Switch can be operated manually:

• Press the top of the rocker switch to turn the connected device ON.
• Press the bottom of the rocker switch to turn the connected device OFF.
• An LED indicator on the switch illuminates to show its location in a dark room.

5.2 Einbindung in das Z-Wave-Netzwerk (Kopplung)

To add the switch to your Z-Wave network:

1. Place your Z-Wave controller into inclusion (pairing) mode. Refer to your controller's instruction manual for specific steps.
2. Once the controller is in inclusion mode, quickly tap the top or bottom of the rocker switch once. The LED indicator on the switch may flash to confirm inclusion.
3. The controller will confirm successful inclusion. You can now control the switch remotely through your Z-Wave network.

Notiz: Pairing typically requires a light, quick tap, not a prolonged press.

5.3 Z-Wave Network Exclusion (Unpairing)

To remove the switch from your Z-Wave network:

1. Place your Z-Wave controller into exclusion (unpairing) mode. Refer to your controller's instruction manual for specific steps.
2. Once the controller is in exclusion mode, quickly tap the top or bottom of the rocker switch once. The LED indicator on the switch may flash to confirm exclusion.
3. The controller will confirm successful exclusion. The switch is now removed from your Z-Wave network.

6. Wartung

• Reinigung: Um den Schalter zu reinigen, wischen Sie ihn mit einem weichen, fusselfreien Tuch ab.amp Tuch. Keine Scheuer- oder Lösungsmittel verwenden.
• Keine vom Benutzer zu wartenden Teile: There are no user-serviceable parts inside the switch. Do not attempt to open or repair the device.
• Firmware-Updates: Any firmware updates would be managed through your Z-Wave controller, if supported.

7. Fehlerbehebung

8. Spezifikationen

9. Garantie und Support

For warranty information and technical support, please refer to the documentation provided with your purchase or visit the JASCO Products webBewahren Sie Ihren Kaufbeleg für Garantieansprüche auf.

JASCO Products provides customer support for their Z-Wave devices. Contact information can typically be found on their official webauf der Website oder auf der Produktverpackung.