Einführung
The Orbit 94162 Buddy Digital Automatic Watering Timer is designed to automate garden watering tasks, providing consistent irrigation for micro-jets, drip irrigation systems, and garden sprinklers. This manual provides instructions for the proper installation, programming, operation, and maintenance of your watering timer.
Produkt überview

Abbildung 1: Vorderseite view of the Orbit 94162 Buddy Digital Automatic Watering Timer, showing the digital display, control buttons, and rotary dial.
This digital watering timer features a user-friendly interface with a large LCD display, intuitive control buttons, and a rotary dial for selecting various programming functions. It is equipped with a diaphragm solenoid valve for reliable and long-lasting performance.
Installation und Setup
1. Einlegen der Batterie
- Ensure the timer is in the 'OFF' position.
- Suchen Sie das Batteriefach auf der Rückseite des Timers.
- Open the compartment and insert two (2) AA alkaline batteries, observing the correct polarity (+/-).
- Close the battery compartment securely. The display should illuminate.
2. Befestigung am Wasserhahn

Figure 2: The watering timer connected to a standard garden faucet with a hose attached.
- Thread the timer onto any standard outdoor garden faucet. Hand-tighten only. Do not use tools.
- Attach your garden hose or irrigation system to the outlet of the timer.
- Turn on the faucet completely. The timer is designed to operate with full water pressure.
Wichtig: When freezing temperatures are expected, timers must be removed from hose faucets to prevent potential freezing damage.
Programmierung und Bedienung

Abbildung 3: Nahaufnahme view of the timer's rotary dial and digital display, showing various programming options.
The timer features a rotary dial with several settings for easy programming:
- UHR EINSTELLEN: Passen Sie die aktuelle Uhrzeit an.
- STARTZEIT: Set the desired time for watering to begin.
- WIE LANG: Determine the duration of each watering cycle.
- WIE OFT: Specify the frequency of watering cycles.
- WAGEN: Activates the programmed watering schedule.
- AUS: Turns off all watering.
1. Set Current Time (SET CLOCK)
- Drehen Sie den Drehknopf auf „UHRZEIT EINSTELLEN“.
- Use the '+' and '-' buttons to adjust the hour. Press the '+' or '-' button to change the value. Hold the button for faster adjustment.
- Press the 'MANUAL' button to switch between AM/PM.
- Verwenden Sie die Tasten „+“ und „-“, um die Minuten einzustellen.
- Turn the dial to the next setting or 'AUTO' to save.
2. Set Start Time (START TIME)
- Turn the dial to 'START TIME'.
- Use the '+' and '-' buttons to set the desired time for watering to begin.
- Press the 'MANUAL' button to switch between AM/PM.
- Turn the dial to the next setting or 'AUTO' to save.
3. Set Watering Duration (HOW LONG)
- Turn the dial to 'HOW LONG'.
- Use the '+' and '-' buttons to set the watering duration from 1 to 240 minutes.
- Turn the dial to the next setting or 'AUTO' to save.
4. Set Watering Frequency (HOW OFTEN)
- Turn the dial to 'HOW OFTEN'.
- Use the '+' and '-' buttons to set the watering frequency. Options include every 6 hours, every 12 hours, or every 1 to 7 days.
- Turn the dial to 'AUTO' to save and activate the program.
5. Automatic Operation (AUTO)
Once all settings are programmed, turn the dial to 'AUTO'. The timer will now operate according to your set schedule. The display will show the current time and the next scheduled watering cycle.
6. Manueller Betrieb
To water manually, press the 'MANUAL' button. Use the '+' and '-' buttons to set the desired manual watering duration. Press 'MANUAL' again to start watering. To stop manual watering, press 'MANUAL' again or turn the dial to 'OFF'.
7. Regenverzögerung
To activate a rain delay, press and hold the '+' button while the dial is in the 'AUTO' position. This will pause the watering schedule for a set period (e.g., 24, 48, 72 hours). Press the '+' button repeatedly to cycle through delay options. The timer will resume its schedule automatically after the delay period.
Wartung
Batteriewechsel
Replace batteries annually or when the low battery indicator appears on the display. Always use fresh AA alkaline batteries. Remove old batteries promptly to prevent leakage.
Reinigung
Clean the exterior of the timer with a damp Mit einem Tuch abwischen. Keine Scheuermittel verwenden und das Gerät nicht in Wasser tauchen.
Überwinterung
Before the first frost, disconnect the timer from the faucet and drain any remaining water. Store the timer indoors in a dry, protected area where temperatures will not drop below freezing. Removing batteries during storage is recommended.
Fehlerbehebung
- Kein Wasserfluss:
- Stellen Sie sicher, dass der Wasserhahn vollständig geöffnet ist.
- Überprüfen Sie den Batteriestand und ersetzen Sie ihn bei Bedarf.
- Verify the timer is in 'AUTO' mode or manual watering is activated.
- Check for debris in the timer's inlet filter.
- Timer not watering at scheduled time:
- Confirm the current time and start time are set correctly.
- Stellen Sie sicher, dass der Timer im Modus „AUTO“ eingestellt ist.
- Check if a rain delay is active.
- Verify battery power.
- Leckagen an Verbindungen:
- Stellen Sie sicher, dass alle Verbindungen handfest angezogen sind.
- Check the rubber washer inside the timer's inlet for proper seating and damage. Replace if necessary.
- Bildschirm ist leer oder dunkel:
- Ersetzen Sie die Batterien durch neue AA-Alkalibatterien.
Technische Daten
| Marke | Orbit |
| Modellnummer | 94162 |
| Farbe | Grün |
| Material | Plastik |
| Produktabmessungen (L x B x H) | 7 x 17 x 20.5 cm |
| Artikelgewicht | 400 Gramm |
| Stromquelle | 2 x AA-Batterien (nicht im Lieferumfang enthalten) |
| Bewässerungsdauer | 1 bis 240 Minuten |
| Bewässerungshäufigkeit | Every 6 hours, 12 hours, or 1 to 7 days |
| Anzahl der Einstellungen | 5 (Set Clock, Start Time, How Long, How Often, Auto/Off) |
| UPC | 05060246190090 |
Garantieinformationen
Detaillierte Garantieinformationen finden Sie auf der offiziellen Website des Herstellers. website or the warranty card included with your product packaging. Keep your purchase receipt as proof of purchase for any warranty claims.
Kundenservice
Should you require technical assistance, have questions regarding product operation, or need to report an issue, please contact Orbit customer support. Contact details can typically be found on the Orbit webStandort oder Produktverpackung.





