Steinbach SPS 100-1T Self-Priming Filter Pump User Manual
Modell: 040917
1. Produktüberschreitungview
The Steinbach SPS 100-1T self-priming filter pump is designed to be the central component of your pool's circulation system. This robust pump features a pre-filter and an integrated timer, making it suitable for pools up to approximately 40,000 liters (10,567 gallons) in volume. It operates on 230V/550W power and offers a pumping capacity of 9,480 liters per hour (158 l/min) with a maximum pump height of 10 meters.
The pump is designed for durability and efficiency, ensuring clean and clear pool water. It is compatible with hose connections of Ø 32/38 mm and can operate with water temperatures up to 35 °C.
Abbildung 1: Überview of the Steinbach SPS 100-1T Self-Priming Filter Pump. This image shows the complete pump unit, including the motor, pump housing, and pre-filter basket.
2. Sicherheitshinweise
- Vor jeglichen Wartungs- oder Reinigungsarbeiten muss die Pumpe vom Stromnetz getrennt werden.
- Um Vibrationen und Bewegungen zu vermeiden, muss die Pumpe auf einer stabilen, ebenen Fläche installiert werden.
- Do not operate the pump dry. Ensure it is always filled with water before starting.
- Halten Sie Kinder und Haustiere während des Betriebs von der Pumpe fern.
- Only use the pump for its intended purpose (pool water filtration).
- Regularly inspect the power cable for damage. Do not use if damaged.
- Ensure all electrical connections are properly sealed and protected from water.
3. Einrichtung und Installation
3.1 Auspacken
Nehmen Sie alle Komponenten vorsichtig aus der Verpackung. Prüfen Sie, ob alle Teile vorhanden und unbeschädigt sind. Die vollständige Bestandsliste finden Sie in der Packliste.
3.2 Platzierung
Position the pump on a firm, level surface, preferably below the water level of the pool for optimal self-priming. Ensure adequate ventilation around the pump to prevent overheating. The pump should be placed in a location protected from direct sunlight and adverse weather conditions.
3.3 Anschlussschläuche
Connect the pool's suction line to the inlet of the pump (the side with the pre-filter) and the return line to the outlet. The pump is designed for Ø 32/38 mm hose connections. Secure all hose connections with appropriate clamps um Lecks zu vermeiden.
Abbildung 2: Nahaufnahme view of the pre-filter inlet with a hose connected. This shows the transparent pre-filter housing and the connection point for the pool's suction hose.
Abbildung 3: Nahaufnahme view of the pump outlet with a hose connected. This illustrates the connection point for the pool's return hose.
3.4 Vorbereiten der Pumpe
Before first use, or after the pump has been drained, it must be primed. Open the pre-filter lid and fill the pre-filter basket and pump housing completely with water. Replace the lid securely. This ensures the pump does not run dry, which can cause damage.
Abbildung 4: View of the pre-filter inlet without a hose attached. This shows the threaded connection for the pre-filter housing.
Abbildung 5: View of the pump outlet without a hose attached. This shows the threaded connection for the outlet hose.
3.5 Elektrischer Anschluss
Connect the pump to a grounded 230V power outlet. Ensure the electrical circuit is protected by a Residual Current Device (RCD) for safety. Do not use extension cords unless absolutely necessary, and ensure they are rated for outdoor use and the pump's power requirements.
4. Bedienungsanleitung
4.1 Starten und Stoppen der Pumpe
Once the pump is primed and all connections are secure, press the EIN/AUS button on the control panel to start the pump. Press it again to stop the pump.
4.2 Verwendung des integrierten Timers
The SPS 100-1T pump features an integrated timer for automated operation. Use the TIMER button to set the desired operating duration. The control panel typically has indicators for various time settings (e.g., 2, 4, 6, 8, 10, 12, 14, 16, 24 hours). Select the appropriate duration based on your pool's size and usage to ensure adequate filtration.
Abbildung 6: Nahaufnahme view of the pump's control panel. This image highlights the ON/OFF and TIMER buttons, along with the indicators for setting the filtration duration.
4.3 Optimal Filtration Time
For optimal water quality, it is generally recommended to filter the entire volume of your pool water at least once per day. The required filtration time depends on the pump's flow rate and your pool's volume. For this pump with a flow rate of 9,480 l/h, a 40,000-liter pool would require approximately 4.2 hours of filtration per day (40,000 L / 9,480 L/h ≈ 4.2 h).
5. Wartung
5.1 Reinigung des Vorfilterkorbs
The pre-filter basket collects larger debris and should be cleaned regularly to maintain pump efficiency.
- Turn off the pump and disconnect it from the power supply.
- Schrauben Sie den transparenten Deckel des Vorfilters ab.
- Remove the pre-filter basket and empty any collected debris.
- Rinse the basket thoroughly with clean water.
- Prüfen Sie den O-Ring-Dichtungsring am Deckel auf Beschädigungen und stellen Sie sicher, dass er sauber ist.
- Place the clean basket back into the housing and securely screw on the lid.
- Entlüften Sie die Pumpe gegebenenfalls erneut, bevor Sie sie wieder in Betrieb nehmen.
5.2 Überwinterung
Before the first frost, the pump must be drained and stored in a frost-free environment.
- Trennen Sie die Pumpe von der Stromversorgung.
- Sämtliche Schläuche abmontieren.
- Remove the drain plug (if present) or tilt the pump to ensure all water drains out.
- Clean the exterior of the pump.
- Lagern Sie die Pumpe an einem trockenen, frostfreien Ort.
6. Fehlerbehebung
| Problem | Mögliche Ursache | Lösung |
|---|---|---|
| Pumpe startet nicht | Keine Stromversorgung; ausgelöster Sicherungsautomat; fehlerhafte Verkabelung. | Check power connection; reset circuit breaker; inspect wiring (consult electrician if unsure). |
| Niedriger Wasserdurchfluss | Clogged pre-filter; air in the system; restricted hoses; low water level in pool. | Clean pre-filter basket; re-prime pump; check hoses for kinks/blockages; ensure adequate pool water level. |
| Pumpe ist laut | Air in the system; debris in impeller; pump running dry; loose connections. | Re-prime pump; clean impeller (professional service recommended); ensure pump is always filled with water; tighten all connections. |
| Wasser tritt aus der Pumpe aus | Loose hose connections; damaged O-rings/seals; cracked housing. | Schlauchklemme festziehenamps; inspect and replace O-rings/seals; contact support for housing damage. |
7. Technische Daten
| Besonderheit | Spezifikation |
|---|---|
| Modellnummer | 040917 |
| Hersteller | Steinbach |
| Bandtage | 230 Volt |
| Leistung | 550 Watt |
| Maximaler Durchfluss | 9,480 Litres per hour (158 l/min) |
| Max Pump Height | 10 Meter |
| Schlauchanschluss | Ø 32/38 mm |
| Maximale Wassertemperatur | 35 °C |
| Maximales Poolvolumen | 40,000 Liter |
| Geräuschpegel | Ca. 70dB |
| Material | Stainless steel (internal components), Plastic (housing) |
| Abmessungen (Paket) | 45.4 x 24.8 x 20.8 cm |
| Gewicht | 6.14 Kilogramm |
| Merkmale | Self-priming, Integrated timer, Pre-filter |
8. Garantie und Support
This product comes with a standard manufacturer's warranty. Please refer to your purchase documentation for specific warranty terms and conditions. For technical support, spare parts, or warranty claims, please contact Steinbach customer service or your authorized dealer.
Steinbach Contact Information:
- WebWebsite: www.steinbach.at
- Modellreferenz: 9008748409179
Bitte halten Sie Ihre Modellnummer (040917) und das Kaufdatum bereit, wenn Sie sich an den Support wenden.
