1. Produktüberschreitungview
The Tekmar 519 Radiant Thermostat is designed to control a single stage of heating within a hydronic system. This non-programmable thermostat offers a straightforward and efficient method for managing the temperature of a specific zone. It features auto cycling to optimize system performance and includes a 079 Slab Sensor for monitoring and protecting slab temperatures against extreme conditions.
Abbildung 1: The Tekmar 519 Radiant Thermostat, a white rectangular device with a digital display and control buttons.
2. Installation und Einrichtung
Proper installation is crucial for the optimal performance of your Tekmar 519 thermostat. If you are unsure about any steps, it is recommended to consult a qualified HVAC technician.
2.1 Sicherheitsvorkehrungen
- Strom ausschalten: Vor der Installation oder Wartung des Thermostats muss immer die Stromzufuhr zum Heizsystem am Hauptsicherungsschalter unterbrochen werden.
- Elektrische Verkabelung: Stellen Sie sicher, dass alle Verkabelungen den örtlichen Elektrovorschriften entsprechen.
- Vermeiden Sie Wasser: Do not install the thermostat in locations where it may be exposed to water or excessive humidity.
2.2 Montage des Thermostats
- Remove the old thermostat (if applicable) and label the existing wires.
- Mount the Tekmar 519 base plate to a suitable indoor wall location, away from direct sunlight, drafts, or heat sources.
- Connect the wires to the appropriate terminals on the thermostat base plate. Refer to the wiring diagram provided with your product packaging for specific connections.
- Install the 079 Slab Sensor according to its specific instructions, ensuring it is properly placed to monitor slab temperature.
- Secure the thermostat faceplate onto the base plate.
2.3 Erste Inbetriebnahme und Konfiguration
- Die Stromversorgung der Heizungsanlage wiederherstellen.
- The thermostat will power on and may display initial setup prompts.
- Follow the on-screen instructions to set the time, date, and any specific system parameters required for your hydronic setup.
3. Bedienungsanleitung
The Tekmar 519 is a non-programmable thermostat, offering simple and direct control over your heating system.
3.1 Temperatur einstellen
- Verwenden Sie die Up Und Runter arrow buttons on the thermostat to adjust the desired room temperature.
- The display will show the current room temperature and the setpoint.
3.2 Modusauswahl
The thermostat typically operates in a single heating mode. If other modes are available (e.g., Off), use the Modus button to cycle through the options.
3.3 Auto Cycling Feature
The Tekmar 519 utilizes an auto cycling feature to calculate and execute the ideal number of heating cycles per hour. This helps to minimize short cycling, conserve energy, and reduce wear and tear on your heating system. This feature operates automatically in the background.
3.4 Slab Sensor Monitoring
The included 079 Slab Sensor continuously monitors the slab temperature to ensure it remains within safe operating limits and provides protection against extreme temperatures. This data is used by the thermostat to optimize radiant heating delivery.
4. Wartung
Regelmäßige Wartung gewährleistet die Langlebigkeit und Effizienz Ihres Thermostats.
- Reinigung: Wischen Sie die Außenseite des Thermostats vorsichtig mit einem weichen, fusselfreien Tuch ab.amp Tuch. Keine Scheuer- oder Lösungsmittel verwenden.
- Batteriewechsel: The thermostat may use batteries for backup power or primary operation. Refer to the product manual for your specific model's battery type and replacement instructions. Typically, a low battery indicator will appear on the display when replacement is needed.
- Jährliche Vorsorgeuntersuchung: It is recommended to have your entire HVAC system, including the thermostat, inspected by a professional annually.
5. Fehlerbehebung
If you encounter issues with your Tekmar 519 thermostat, try the following steps:
| Problem | Mögliche Ursache | Lösung |
|---|---|---|
| Kein Display/Keine Stromversorgung | No power to the thermostat; dead batteries. | Check the circuit breaker for your heating system. Replace batteries if applicable. |
| Heizungsanlage reagiert nicht | Falscher Modus ausgewählt; Verkabelungsproblem; Systemstörung. | Ensure the thermostat is set to "Heat" mode. Verify wiring connections. Contact a professional if the issue persists. |
| Ungenaue Temperaturanzeige | Thermostat location affected by drafts/heat sources; sensor malfunction. | Ensure the thermostat is not in direct sunlight or near heat/cold sources. Check slab sensor connection. |
| Slab overheating/underheating | Slab sensor issue; system calibration needed. | Verify slab sensor placement and connection. Consult the full product manual or a professional for calibration. |
6. Spezifikationen
- Marke: Tekmar
- Modell: 519
- Bandtage: 24 Volt
- Steuerungstyp: Tastensteuerung
- Hintergrundbeleuchtung: Ja
- Hitze S.tages: Ein Stage Hitze
- Included Sensor: 079 Slab Sensor
- Datum der Erstveröffentlichung: 23. März 2012
7. Garantie und Support
For detailed warranty information and technical support, please refer to the official Tekmar documentation included with your product or visit the Tekmar Store on Amazon oder ihr Beamter webWebsite.
Es wird empfohlen, den Kaufbeleg als Kaufnachweis für Garantieansprüche aufzubewahren.
8. Produktvideos
Für dieses Produkt sind keine offiziellen Verkäufervideos verfügbar.