1. Einleitung
Thank you for choosing the Marshall DSL100HR Guitar Amplifier Head. This 100-watt all-valve amplifier head is designed to deliver a wide range of classic Marshall tones, from pristine cleans to high-gain distortion. It features two footswitchable channels, Classic Gain and Ultra Gain, each with two modes, providing four distinct sounds. Additional features include dedicated resonance control, two master volume controls, digital reverb, high and low power settings, and a Softube emulated output for direct recording or silent practice.
This manual provides essential information for the safe and effective operation of your DSL100HR amplifier. Please read it thoroughly before connecting or operating the unit.
Figure 1: Marshall DSL100HR Guitar Amplifier Head, front view. This image displays the amplifier's robust construction and classic Marshall aesthetic, featuring the control panel and input jack.
2. Sicherheitshinweise
To prevent electric shock, fire, or damage to the amplifier, always observe the following safety precautions:
- Stromversorgung: Verbinden Sie amplifier only to an AC power supply of the voltage specified on the rear panel. Ensure the power cable is in good condition and properly grounded.
- Belüftung: Blockieren Sie keine Lüftungsöffnungen. Sorgen Sie für ausreichende Luftzirkulation um das Gerät herum. ampKühlmittel, um eine Überhitzung zu verhindern.
- Feuchtigkeit: Setzen Sie die ampDas Gerät vor Regen, Feuchtigkeit und übermäßiger Luftfeuchtigkeit schützen. Flüssigkeiten vom Gerät fernhalten.
- Wartung: Versuchen Sie nicht, das Gerät zu warten amplifier yourself. Refer all servicing to qualified service personnel. High voltages sind innerhalb der vorhanden amplifier, even when switched off.
- Lautsprecheranschlüsse: Verbinden Sie immer die amplifier to a suitable speaker cabinet with the correct impedance before powering on. Operating without a speaker load can damage the output transformer.
- Tube Heat: Vacuum tubes operate at high temperatures. Avoid touching them and allow sufficient cooling time after use.
- Gehörschutz: Das amplifier can produce high sound pressure levels. Prolonged exposure to high volumes can cause permanent hearing damage. Use appropriate hearing protection.
3. Einrichtung
3.1 Auspacken
Entfernen Sie vorsichtig die amplifier from its packaging. Retain all packaging materials for future transport or storage. Inspect the amplifier for any signs of damage incurred during shipping. If damage is found, contact your dealer immediately.
3.2 Connecting to a Speaker Cabinet
The DSL100HR requires connection to an external speaker cabinet. Ensure the speaker cabinet's impedance matches one of the amplifier's output jacks (16 Ohm, 8 Ohm, or 4 Ohm). Use a high-quality speaker cable (not a guitar cable) for this connection.
- For a single 16 Ohm cabinet, connect to the '16 Ohm' jack.
- For a single 8 Ohm cabinet, connect to one of the '8 Ohm' jacks.
- For two 16 Ohm cabinets, connect each to an '8 Ohm' jack.
- For a single 4 Ohm cabinet, connect to one of the '4 Ohm' jacks.
- For two 8 Ohm cabinets, connect each to a '4 Ohm' jack.
Wichtig: Betreiben Sie niemals die amplifier without a speaker load connected to the appropriate output jack.
3.3 Stromanschluss
Connect the supplied power cable to the IEC inlet on the rear panel of the amplifier and then to a grounded mains power outlet.
3.4 Anschließen einer Gitarre
Connect your guitar to the 'INPUT' jack on the front panel using a standard instrument cable.
3.5 Fußschalteranschluss
Connect the supplied footswitch to the 'FOOTSWITCH' jack on the rear panel. This allows remote switching between channels and reverb on/off.
4. Bedienungsanleitung
4.1 Ein-/Ausschalten
- Stellen Sie sicher, dass alle Lautstärkeregler auf Minimum eingestellt sind.
- Switch the 'POWER' switch to the ON position.
- Wait approximately 30-60 seconds for the tubes to warm up, then switch the 'STANDBY' switch to the ON position. The amplifier ist nun einsatzbereit.
- To power off, reverse the sequence: 'STANDBY' to OFF, then 'POWER' to OFF.
4.2 Bedienelemente auf der Vorderseite
The DSL100HR features a comprehensive set of controls:
- Classic Gain Channel:
- Volumen: Controls the output level of the Classic Gain channel.
- Gewinnen: Passt die Menge an Vor-amp gain for the Classic Gain channel.
- Clean/Crunch Switch: Selects between a clean tone and a crunchy overdrive within the Classic Gain channel.
- Ultra Gain Channel:
- Volumen: Controls the output level of the Ultra Gain channel.
- Gewinnen: Passt die Menge an Vor-amp gain for the Ultra Gain channel, from aggressive crunch to searing lead tones.
- OD1/OD2 Switch: Selects between two different overdrive voicings within the Ultra Gain channel.
- Equalization (Shared):
- Höhen, Mitten, Bässe: Standard tone controls to shape the amplifier's frequency response.
- Gegenwart: Adds high-end sparkle and cut to the overall sound.
- Resonanz: Adjusts the low-end response and depth of the ampschwerer.
- Tonverschiebung: A push-button switch that re-configures the amplifier's EQ for a more modern, mid-scooped sound.
- Nachhall: Regelt die Intensität des eingebauten digitalen Hall-Effekts.
- Master Volume 1 & 2: Two independent master volume controls allow for different overall output levels, useful for solos or rhythm sections. These can be switched via the footswitch.
- Schalter für hohe/niedrige Leistung: Verringert die amplifier's output power from 100W to 50W, allowing for lower volume operation while maintaining tube tone.
4.3 Anschlüsse auf der Rückseite
- Lautsprecherausgänge: Multiple jacks for connecting speaker cabinets with various impedance ratings (16 Ohm, 8 Ohm, 4 Ohm).
- FX-Loop (Send/Return): Allows connection of external effects pedals or processors. The FX loop can be bypassed.
- Softube Emulated Output: A 6.35mm jack providing a direct, cabinet-emulated signal for recording or connecting to a PA system.
- MIDI-Eingang: For external MIDI control of ampLifier-Funktionen.
- Fußschalter: Connects the supplied footswitch for remote control of channels and reverb.
5. Wartung
5.1 Schlauchwechsel
The DSL100HR uses 4 x ECC83 preamp tubes and 4 x EL34 power tubes. Tubes have a finite lifespan and will eventually need replacement. Symptoms of worn tubes include loss of volume, reduced tone quality, excessive noise, or intermittent operation. Tube replacement should ideally be performed by a qualified technician, as it involves working with high voltages and proper biasing of new power tubes is crucial for optimal performance and longevity.
5.2 Reinigung
Reinigen Sie die amplifier's exterior with a soft, dry cloth. Do not use abrasive cleaners, solvents, or waxes. Ensure the ampDer Verstärker wird vor der Reinigung vom Stromnetz getrennt.
5.3 Speicherung
Bei längerer Nichtbenutzung lagern Sie die amplifier in a dry, temperature-controlled environment, away from direct sunlight and extreme temperatures. Using a protective cover can help prevent dust accumulation.
6. Fehlerbehebung
If you experience issues with your DSL100HR, consult the following troubleshooting guide before seeking professional service:
| Problem | Mögliche Ursache | Lösung |
|---|---|---|
| Kein Ton | Power cable disconnected, standby switch off, speaker not connected, faulty cables, guitar volume down, faulty tubes. | Check power and standby switches. Ensure speaker cable is securely connected to the correct impedance jack. Test with different instrument and speaker cables. Check guitar volume. Consult a technician for tube issues. |
| Hum or excessive noise | Ground loop, faulty cables, proximity to other electronic devices, worn tubes. | Ensure all equipment is on the same power circuit. Try different cables. Move amplifier away from other electronics. Consult a technician for tube inspection. |
| Schwacher oder verzerrter Ton | Worn tubes, incorrect speaker impedance, faulty speaker. | Check speaker impedance match. Test with a different speaker cabinet. Consult a technician for tube replacement. |
| Footswitch not working | Footswitch cable disconnected or faulty, footswitch malfunction. | Ensure footswitch cable is securely connected. Test with a known working footswitch if available. |
7. Spezifikationen
- Modell: M-DSL100HR-U
- Ausgang Wattage: 100 Watt (umschaltbar auf 50 Watt)
- Ventile: 4 x ECC83 (preamp), 4 x EL34 (power amp)
- Kanäle: 2 (Classic Gain, Ultra Gain) with 2 modes each
- Steuerung: Volume, Gain (x2), Treble, Middle, Bass, Presence, Resonance, Reverb, Master Volume (x2), Tone Shift, Clean/Crunch, OD1/OD2, High/Low Power
- Eingänge: 1 x 6.35mm Instrument Input
- Ausgaben: Speaker Outputs (1x16 Ohm, 2x8 Ohm, 2x4 Ohm), Softube Emulated Output (6.35mm)
- Effektschleife: Series FX Loop (Send/Return)
- MIDI: MIDI-Eingang
- Fußschalter: Included (channel/reverb switching)
- Artikelgewicht: 48.7 Pfund (22.09 kg)
- Produktabmessungen: 13.8 x 33.7 x 15.9 Zoll (35.05 x 85.6 x 40.39 cm)
- Materialart: Metall
- Energiequelle: Kabelgebundene Elektrik
8. Garantie und Support
For warranty information, technical support, or service inquiries, please refer to the warranty card included with your product or visit the official Marshall Amplifizierung webBewahren Sie Ihren Kaufbeleg für Garantieansprüche auf.
Marshall Amplification is committed to providing high-quality products and customer satisfaction. Should you require assistance beyond the scope of this manual, please contact authorized Marshall service centers or customer support.
