Produkt überview
The Emtek 7103 Passage Set is a high-quality knobset designed for doors that do not require a locking mechanism, such as closet doors, hallway doors, or pantry doors. This set includes a Madison Black Knob and a #3 Wrought Steel Rosette with a Flat Black Steel (FBS) finish. It is manufactured by Emtek and includes a standard rotation latch and strike plate. The knobset is designed for a standard 2-1/8 inch door preparation. The standard latch is for a 2-3/8 inch backset, with a 2-3/4 inch backset available if specified.
This image displays the Emtek 7103 Passage Set, featuring a round Madison Black Knob mounted on a rectangular Flat Black Wrought Steel Rosette. The knob has a smooth, glossy black finish, contrasting with the textured matte black finish of the rosette.
Setup und Installation
This section provides instructions for the proper setup and installation of your Emtek 7103 Passage Set.
Bevor Sie beginnen
- Ensure all components are present: knobset, rosette, latch, strike plate, and mounting screws.
- Verify door thickness and backset requirements. Standard backset is 2-3/8 inches. If 2-3/4 inches is required, ensure you have the correct latch.
- Tools required: Phillips head screwdriver, tape measure, pencil.
Installationsschritte
- Bereiten Sie die Tür vor: Ensure the door has a standard 2-1/8 inch bore hole for the knobset and a 1-inch bore hole for the latch.
- Installieren Sie den Riegel: Insert the latch into the edge of the door, ensuring the bevel faces the door frame. Secure with screws.
- Install the Exterior Knob/Rosette: Place the exterior knob and rosette assembly through the 2-1/8 inch bore hole, aligning the spindle with the latch mechanism.
- Install the Interior Knob/Rosette: Place the interior knob and rosette assembly onto the spindle, aligning the mounting posts with the holes on the exterior rosette.
- Sichern Sie die Versammlung: Insert and tighten the mounting screws through the interior rosette into the exterior rosette. Do not overtighten.
- Montieren Sie die Schließplatte: Mark and chisel the door frame for the strike plate. Secure the strike plate with screws, ensuring the latch engages smoothly.
- Testbetrieb: Rotate the knobs to ensure the latch retracts and extends freely. Check for smooth operation from both sides of the door.
Bedienungsanleitung
The Emtek 7103 Passage Set is designed for doors that do not require locking, such as closet doors, hallway doors, or pantry doors. It allows for free passage from both sides at all times.
- To open the door, simply turn the knob in either direction. The latch bolt will retract, allowing the door to open.
- To close the door, push the door shut. The latch bolt will automatically engage with the strike plate, holding the door closed.
Wartung
Proper maintenance will ensure the longevity and smooth operation of your Emtek 7103 Passage Set.
- Reinigung: Clean the knob and rosette surfaces with a soft, damp cloth. Avoid abrasive cleaners, solvents, or polishes that may damage the finish.
- Schmierung: Periodically apply a small amount of silicone-based lubricant to the latch mechanism to ensure smooth operation. Do not use oil-based lubricants as they can attract dust and grime.
- Befestigungsschrauben: Over time, mounting screws may loosen. Periodically check and gently tighten any loose screws to maintain stability. Do not overtighten.
- Inspektion: Regularly inspect the knobset for any signs of wear, damage, or misalignment.
Fehlerbehebung
| Problem | Mögliche Ursache | Lösung |
|---|---|---|
| Der Knopf ist locker oder wackelig. | Befestigungsschrauben sind lose. | Tighten the mounting screws on the interior rosette. |
| Der Verschluss lässt sich nicht reibungslos zurückziehen. | Mangelnde Schmierung; Ablagerungen im Mechanismus. | Apply silicone-based lubricant to the latch bolt. Clean any visible debris. |
| Die Tür schließt nicht richtig oder klappert. | Strike plate misalignment; worn latch. | Adjust the strike plate position. If latch is worn, consider replacement. |
| Knob is stiff to turn. | Spindle misalignment; internal mechanism friction. | Loosen mounting screws slightly, adjust knob position, then retighten. Lubricate internal mechanism if accessible. |
Technische Daten
- Modell: Emtek 7103 Passage Set
- Material: Wrought Steel
- Knopfstil: Madison Black Knob
- Rosette Style: #3 Rosette
- Beenden: Flat Black Steel (FBS)
- Türvorbereitung: Standard 2-1/8" bore hole
- Dornmaß: Standard 2-3/8" (2-3/4" available upon request)
- UPC: 751125555226
Garantie und Support
Emtek products are manufactured to high-quality standards. For specific warranty information regarding your Emtek 7103 Passage Set, please refer to the documentation provided with your purchase or visit the official Emtek webDie Garantiebedingungen können je nach Website variieren.
For technical support, product inquiries, or assistance with installation or troubleshooting, please contact Emtek customer service directly. Their contact information can typically be found on their official webor oder innerhalb der Produktverpackung.
Hersteller: Emtek
Offiziell WebWebsite: www.emtek.com
