Emtek Wilshire 8579 Single Sided Deadbolt

1. Einleitung

Thank you for choosing the Emtek Wilshire 8579 Single Sided Deadbolt. This deadbolt is designed to provide enhanced security for your doors with its key lock mechanism and antique-style aesthetic. This manual provides essential information for proper installation, operation, and maintenance to ensure optimal performance and longevity of your deadbolt.

2. Sicherheitshinweise

• Tragen Sie bei der Installation stets geeignete Schutzausrüstung, wie z. B. Handschuhe und Augenschutz.
• Ensure all components are handled carefully to prevent damage or injury.
• Do not use power tools on settings that could overtighten screws or damage the door or deadbolt components.
• Halten Sie Kleinteile von Kindern fern, um Erstickungsgefahr vorzubeugen.
• If you are unsure about any step of the installation process, consult a qualified locksmith or professional installer.

3. Packungsinhalt

Vergewissern Sie sich vor Beginn der Installation, dass alle Teile vorhanden sind:

• Exterior Key Cylinder Assembly (with square escutcheon)
• Interior Thumb Turn Assembly (with square escutcheon)
• Riegelschlossmechanismus
• Schlagplatte
• Reinforcement Plate (for strike plate)
• Befestigungsschrauben (verschiedene Größen)
• Keys (typically 2)

4. Einrichtung und Installation

This section outlines the steps for installing your Emtek Wilshire 8579 Single Sided Deadbolt. Ensure your door is prepared with the necessary bore holes (typically 2-1/8 inch for the main body and 1 inch for the latch).

4.1 Komponenten identifizieren

This image displays the two main components of the Emtek Wilshire 8579 Single Sided Deadbolt. On the left is the exterior key cylinder with a square escutcheon plate. On the right is the interior thumb turn mechanism, also with a square escutcheon plate, which allows for manual locking and unlocking from the inside.

4.2 Install the Latch Mechanism

1. Insert the deadbolt latch mechanism into the 1-inch bore hole on the edge of the door. Ensure the word "TOP" (if present) is facing upwards.
2. Secure the latch mechanism with the two small screws provided.

4.3 Install the Exterior Key Cylinder

1. Insert the exterior key cylinder assembly into the 2-1/8 inch bore hole from the outside of the door.
2. Ensure the tailpiece (the small metal bar extending from the back of the cylinder) passes through the slot in the latch mechanism.

4.4 Install the Interior Thumb Turn Assembly

1. From the inside of the door, align the interior thumb turn assembly with the exterior cylinder.
2. Ensure the tailpiece from the exterior cylinder engages correctly with the thumb turn mechanism.
3. Secure both assemblies together using the long mounting screws provided. Tighten screws evenly until snug, but do not overtighten.

4.5 Install the Strike Plate

1. Close the door and mark the center of the deadbolt latch on the door frame.
2. Chisel out a recess for the strike plate and reinforcement plate so they sit flush with the door frame.
3. Drill a 1-inch hole approximately 1 inch deep for the deadbolt to extend into.
4. Install the reinforcement plate, then the strike plate, securing them with the longer screws provided.

4.6 Testbetrieb

With the door open, test the deadbolt by turning the thumb turn and using the key from the exterior. Ensure the bolt extends and retracts smoothly without binding. Close the door and test again to ensure proper alignment with the strike plate.

5. Bedienungsanleitung

5.1 Locking the Deadbolt

• Von außen: Insert the key into the keyway and turn it clockwise until the deadbolt fully extends into the door frame. Remove the key.
• Aus dem Inneren: Turn the thumb turn clockwise until the deadbolt fully extends into the door frame.

5.2 Unlocking the Deadbolt

• Von außen: Insert the key into the keyway and turn it counter-clockwise until the deadbolt fully retracts. Remove the key.
• Aus dem Inneren: Turn the thumb turn counter-clockwise until the deadbolt fully retracts.

6. Wartung

• Reinigung: Clean the deadbolt's exterior surfaces with a soft, damp Mit einem Tuch abwischen. Vermeiden Sie Scheuermittel oder aggressive Chemikalien, da diese die Oberfläche beschädigen können.
• Schmierung: Periodically apply a small amount of graphite lubricant or a silicone-based spray lubricant into the keyway and the latch mechanism to ensure smooth operation. Do not use oil-based lubricants, as they can attract dust and grime.
• Anziehen: Check mounting screws periodically and tighten if necessary to prevent loosening over time.

7. Fehlerbehebung

8. Spezifikationen

• Marke: Emtek
• Modell: Wilshire 8579 Single Sided Deadbolt
• Schlosstyp: Key Lock (Single Sided)
• Material: Metall
• Stil: Antiquität
• Form: Round (deadbolt mechanism), Square (escutcheon plates)
• Controller-Typ: Mechanical knob (thumb turn)
• Empfohlene Verwendung: Securing interior doors in residential or commercial buildings with traditional/vintagInnenausstattung im E-Stil
• UPC: 789704091766

9. Garantie und Support

Emtek products are manufactured to high-quality standards. Specific warranty details are typically provided with the product packaging or can be found on the official Emtek webBitte bewahren Sie Ihren Kaufbeleg für Garantieansprüche auf.

For technical assistance, replacement parts, or further inquiries, please contact Emtek customer support through their official webWebsite oder die Kontaktinformationen, die Sie mit Ihren Kaufunterlagen erhalten haben.