WAGO 286-364 Schaltrelaismodul – Benutzerhandbuch

1. Produktüberschreitungview

The WAGO 286-364 Switching Relay Module is designed for industrial electrical applications, converting a 24VDC input signal to control a 250VAC, 5AMP output. This module is a critical component for various control systems, offering reliable switching capabilities.

Zu den Hauptmerkmalen gehören:

• Eingangslautstärketage: 24 V Gleichstrom
• Ausgangsvolumentage: 250 V Wechselstrom
• Ausgangsstrom: 5AMP
• Function: Switching Relay Module
• Category: Panel Accessories, Relay/Socket

Abbildung 1: Überview of three WAGO 286-364 Switching Relay Modules, showcasing their compact design and grey housing.

2. Einrichtung und Installation

Proper installation is crucial for the safe and effective operation of the WAGO 286-364 module. Ensure all power sources are disconnected before beginning installation.

2.1. Montage

The module is designed for panel mounting. Secure it firmly using appropriate fasteners or DIN rail clips if applicable to your specific model variant. Ensure adequate ventilation around the module to prevent overheating.

2.2. Kabelverbindungen

Refer to the terminal markings on the module for correct wiring. The module typically features input terminals for 24VDC control signals and output terminals for the 250VAC load.

• Verbinden Sie 24 V Gleichstrom control signal to the designated input terminals (e.g., R1+, R2-).
• Verbinden Sie 250 V Wechselstrom load to the output terminals (e.g., 13, 14).
• Stellen Sie sicher, dass alle Verbindungen sicher und ordnungsgemäß isoliert sind, um Kurzschlüsse zu vermeiden.

Abbildung 2: Ausführlich view of the module's connection pins, highlighting the robust design for secure wiring.

Abbildung 3: Oben view of the modules, indicating the 'TEST' points and model number for identification and testing purposes.

3. Bedienungsanleitung

Once properly installed and wired, the WAGO 286-364 module operates by receiving a 24VDC signal to switch the 250VAC output. The module acts as an interface between low-voltage control circuits and higher-voltage lädt.

• Wenn ein 24 V Gleichstrom signal is applied to the input terminals, the internal relay will energize.
• Upon energization, the output contacts will switch, allowing the 250 V Wechselstrom current to flow to the connected load.
• When the 24VDC input signal is removed, the relay will de-energize, opening the output contacts and disconnecting the 250VAC load.

Abbildung 4: Seite view of the modules, showing the indicator LED which illuminates when the relay is energized, and clearly marked input/output terminals.

3.1. Anzeige-LED

The module is equipped with an indicator LED (visible in Figure 4) that provides visual feedback on the relay's status. The LED illuminates when the 24VDC input signal is present and the relay is energized, confirming proper operation.

4. Wartung

The WAGO 286-364 Switching Relay Module is designed for long-term, maintenance-free operation under normal industrial conditions. However, periodic inspection is recommended to ensure optimal performance and safety.

• Sichtprüfung: Regularly check the module for any signs of physical damage, discoloration, or loose connections.
• Reinigung: Reinigen Sie die Außenseite des Moduls bei Bedarf vorsichtig mit einem trockenen, weichen Tuch. Verwenden Sie keine Scheuermittel oder Lösungsmittel.
• Verbindungsintegrität: Überprüfen Sie regelmäßig, ob alle Kabelverbindungen fest sitzen und frei von Korrosion sind.

Always disconnect power to the module and associated circuits before performing any maintenance or inspection.

5. Fehlerbehebung

If the WAGO 286-364 module is not functioning as expected, consider the following troubleshooting steps:

• Module Not Switching:
  • Überprüfen Sie, ob die 24 V Gleichstrom input signal is present and correctly wired to the input terminals.
  • Check if the indicator LED on the module is illuminated when the input signal is applied. If not, there may be an issue with the input signal or the module itself.
• Keine Ausgangsleistung:
  • Stellen Sie sicher, dass 250 V Wechselstrom power source for the load is active and correctly wired to the output terminals.
  • Confirm that the load itself is functional and not drawing excessive current that could damage the module or trip protective devices.
• Überhitzung:
  • Prüfen Sie, ob für ausreichende Belüftung rund um das Modul gesorgt ist.
  • Ensure the load current does not exceed the module's 5AMP Bewertung.

If issues persist after following these steps, contact a qualified electrician or WAGO technical support.

6. Spezifikationen

7. Garantie und Support

Specific warranty details for the WAGO 286-364 Switching Relay Module are typically provided at the point of purchase or through official WAGO documentation. Please refer to your purchase invoice or the manufacturer's webDie aktuellsten Garantieinformationen finden Sie auf der entsprechenden Webseite.

For technical support, product inquiries, or assistance with troubleshooting beyond the scope of this manual, please contact WAGO directly through their official channels. Contact information can usually be found on the WAGO webStandort oder Produktverpackung.