King Electric TKIT-2B Double Pole Built-in Thermostat Kit

1. Zu Endeview

This manual provides instructions for the installation, operation, and maintenance of the King Electric TKIT-2B Double Pole Built-in Thermostat Kit. This kit is designed for use with specific King Electric electric heater models, including PX, KT, KTW, PAW, W, and WHF. It functions as a snap-action, single-pole or double-pole integrated thermostat.

2. Wichtige Sicherheitshinweise

WARNING: Risk of Electric Shock. Disconnect power before installation or servicing.

• Die Installation muss von einem qualifizierten Elektriker gemäß allen lokalen und nationalen Elektrovorschriften durchgeführt werden.
• Ensure the power supply to the heater is completely disconnected at the circuit breaker before beginning any work.
• Überprüfen Sie, ob das Volumentage and current ratings of the thermostat are compatible with your heater model.
• Do not operate the heater without the thermostat cover properly installed.
• Halten Sie Kinder von elektrischen Komponenten fern.

3. Packungsinhalt

Carefully unpack the kit and ensure all items are present and undamaged. If any parts are missing or damaged, contact your retailer immediately.

• TKIT-2B Thermostat Module
• Mounting Hardware (screws, nuts, etc., as applicable)
• Bedienungsanleitung (dieses Dokument)

4. Installationsanweisungen

This thermostat kit is designed for field installation or replacement in compatible King Electric heaters. Refer to your specific heater's manual for detailed access instructions.

1. Stromversorgung trennen: Ensure the main power supply to the heater is turned OFF at the circuit breaker before proceeding. Verify with a voltage Tester.
2. Access Heater Compartment: Remove the front cover or access panel of your King Electric heater to expose the wiring compartment where the thermostat will be installed. (Refer to your heater's specific manual for cover removal.)
3. Verkabelung identifizieren: Locate the designated thermostat wiring connections within the heater. The TKIT-2B is a double-pole thermostat, meaning it interrupts both hot legs of a 240V circuit.
4. Thermostat montieren: Secure the TKIT-2B thermostat module into the designated mounting location within the heater's control compartment using the provided hardware. Ensure it is firmly seated.
5. Drahtverbindungen:
   • Connect the incoming power wires to the appropriate terminals on the thermostat.
   • Connect the heater element wires to the corresponding output terminals on the thermostat.
   • Ensure all connections are tight and secure. Follow the wiring diagram provided with your heater or the thermostat kit if available.
6. Abdeckung ersetzen: Carefully replace the heater's front cover or access panel, ensuring no wires are pinched.
7. Strom wiederherstellen: Schalten Sie die Hauptstromversorgung am Sicherungsautomaten wieder ein.
8. Testbetrieb: Proceed to the "Operation" section to test the thermostat's functionality.

Note: For single-pole applications, consult a qualified electrician or the heater's specific wiring diagram for proper connection.

5. Bedienungsanleitung

The TKIT-2B is a mechanical, non-programmable thermostat designed for simple temperature control.

1. Temperatur einstellen: Rotate the thermostat knob (if exposed on the heater's exterior) clockwise to increase the desired temperature setting, and counter-clockwise to decrease it.
2. Heizzyklus: When the ambient room temperature falls below the set temperature, the thermostat will activate the heater. When the room temperature reaches the set point, the thermostat will turn off the heater.
3. AUS-Position: Some heater models may have an "OFF" position integrated with the thermostat knob. Turning the knob fully counter-clockwise will typically turn off the heater.

Note: Allow some time for the room temperature to stabilize after making adjustments.

6. Wartung

The King Electric TKIT-2B thermostat requires minimal maintenance.

• Reinigung: Periodically, gently wipe the exterior of the thermostat knob and surrounding area with a soft, dry cloth. Do not use abrasive cleaners or solvents.
• Inspektion: Annually, or if you suspect an issue, have a qualified electrician inspect the wiring connections for tightness and signs of wear. Ensure the thermostat is free from dust buildup.
• Keine vom Benutzer zu wartenden Teile: The internal components of the thermostat are not user-serviceable. Do not attempt to open or repair the thermostat module.

7. Fehlerbehebung

If your heater is not operating as expected after installing the TKIT-2B thermostat, refer to the following common issues and solutions:

If troubleshooting steps do not resolve the issue, contact King Electric customer support or a qualified electrician.

8. Spezifikationen

• Modell: TKIT-2B
• Typ: Double Pole Built-in Thermostat Kit
• Kompatibilität: King Electric heater models PX, KT, KTW, PAW, W, WHF
• Steuerungstyp: Tastensteuerung
• Konnektivitätsprotokoll: W-lan
  Notiz: While product specifications list Wi-Fi connectivity, the TKIT-2B is a mechanical, non-programmable thermostat. Please refer to your heater's specific features for smart connectivity options.
• Hintergrundbeleuchtung: NEIN
• UPC: 093319173473

9. Garantie und Support

For warranty information, please refer to the documentation included with your King Electric heater or visit the official King Electric webBewahren Sie Ihren Kaufbeleg als Kaufnachweis auf.

For technical support or assistance, please contact King Electric customer service. Contact details can typically be found on the manufacturer's website or in your heater's manual.

König Elektro WebWebsite: www.king-electric.com