Marmitek Bell ME WHT Drahtlose Klingel Bedienungsanleitung

Produkt überview

The Marmitek Bell ME WHT is a wireless chime designed to extend the audible notification of your Marmitek Buzz LO video doorbell. This battery-operated unit offers flexible placement throughout your home, ensuring you never miss a visitor, whether you are in the garden, attic, or another room. It connects wirelessly via RF to the Buzz LO and can be paired with multiple Buzz LO units or have multiple Bell ME chimes connected to a single Buzz LO.

Front view of the Marmitek Bell ME WHT wireless chime, white square device with a speaker grille and two small indicator lights.

Abbildung 1: Front view of the Marmitek Bell ME WHT wireless chime. This white, square device features a central speaker grille and two small indicator lights on the left side, displaying its compact and minimalist design.

Packungsinhalt

Stellen Sie sicher, dass alle Teile vorhanden sind, bevor Sie mit der Installation fortfahren.

1 x Marmitek Bell ME WHT Wireless Chime
Benutzerhandbuch (dieses Dokument)

Notiz: Für den Betrieb werden 3 AA-Batterien benötigt, die nicht im Lieferumfang enthalten sind.

Setup und Installation

Batterien einlegen:
Locate the battery compartment on the back of the Bell ME WHT. Insert 3 x AA batteries, ensuring correct polarity (+/-). Close the battery compartment cover securely.

Abbildung 2: Seite view of the Bell ME WHT, illustrating its compact profile and the location of a small port, possibly for power or configuration, though primarily battery-operated.
Pairing with Buzz LO Video Doorbell:
The Bell ME WHT must be paired with a Marmitek Buzz LO video doorbell to function. Follow these steps:
- Ensure your Buzz LO video doorbell is powered on and operational.
- On the Bell ME WHT, locate the pairing button. This is typically a small button often indicated by a gear icon or similar symbol.
- Press and hold the pairing button on the Bell ME WHT for a few seconds until an indicator light flashes, signifying it is in pairing mode.
- Within a short timeframe (usually 10-30 seconds), press the doorbell button on your Buzz LO video doorbell.
- The Bell ME WHT should chime or its indicator light should change to a solid state, confirming successful pairing.
Notiz: You can pair multiple Bell ME chimes to a single Buzz LO, or a single Bell ME chime to multiple Buzz LO doorbells. Repeat the pairing process for each additional unit.
Abbildung 3: Seite view of the Bell ME WHT, highlighting three circular buttons. These buttons are typically used for adjusting volume levels or selecting different chime melodies.
Platzierung:
Due to its battery operation, the Bell ME WHT can be placed anywhere within the wireless range of your Buzz LO doorbell. Consider placing it in areas where the doorbell sound might not be easily heard, such as the garden, attic, basement, or a separate office/practice room.

Bedienungsanleitung

Glockenspielfunktion: Once successfully paired, the Bell ME WHT will sound a chime whenever the Buzz LO video doorbell button is pressed.
Lautstärkeregelung: Use the buttons on the side of the Bell ME WHT (refer to Figure 3) to adjust the volume of the chime. Typically, there are dedicated buttons for increasing und decreaasing Volumen.
Melodieauswahl: The Bell ME WHT may offer multiple chime melodies. Use the designated button (often one of the side buttons) to cycle through available melodies.

Wartung

Batteriewechsel: When the chime sound becomes weak or the indicator light signals low battery, replace the 3 x AA batteries. Always use fresh, high-quality batteries for optimal performance.
Reinigung: Clean the exterior of the Bell ME WHT with a soft, dry cloth. Do not use abrasive cleaners or solvents.
Umgebungsbedingungen: The Bell ME WHT is not water-resistant. Avoid exposing it to moisture, direct sunlight, or extreme temperatures.

Fehlerbehebung

Problem	Mögliche Ursache	Lösung
Bell ME WHT does not chime.	Die Batterien sind leer oder falsch eingelegt. Not paired with Buzz LO. Außerhalb der Funkreichweite. Buzz LO is not functioning.	Ersetzen Sie die Batterien durch neue und achten Sie dabei auf die richtige Polarität. Repeat the pairing process (see "Setup and Installation"). Move the Bell ME WHT closer to the Buzz LO. Check the status and functionality of your Buzz LO video doorbell.
Chime sound is too low or distorted.	Schwache Batterie. Die Lautstärkeeinstellung ist zu niedrig.	Batterien ersetzen. Increase the volume using the side buttons.
Cannot pair Bell ME WHT with Buzz LO.	Fehlerhaftes Kopplungsverfahren. Störungen durch andere drahtlose Geräte. Bell ME WHT is not compatible with your doorbell (only works with Buzz LO).	Ensure you follow the pairing steps precisely. Temporarily move other wireless devices away during pairing. Verify that your doorbell is a Marmitek Buzz LO model.

Technische Daten

Besonderheit	Detail
Modellnummer	Bell ME WHT
Hersteller	Marmitek
Farbe	Weiß
Abmessungen (L x B x H)	7.5 x 7.5 x 3 cm
Gewicht	160 g
Stromquelle	3 x AA-Batterien (nicht im Lieferumfang enthalten)
Bandtage	4.5 V Gleichstrom
Drahtlose Frequenz	450–470 MHz
Maximale Funkreichweite	300 Meters (open field)
Wasserbeständigkeit	Nicht wasserbeständig
Kompatibilität	Exclusively with Marmitek Buzz LO video doorbell

Garantie und Support

Marmitek products are designed and manufactured to high quality standards. For information regarding warranty terms and conditions, please refer to the warranty card included with your purchase or visit the official Marmitek website. For technical support, troubleshooting assistance, or further inquiries, please contact Marmitek customer service through their official channels.

Official Marmitek WebWebsite: www.marmitek.com