OLIGHT Baldr Mini Benutzerhandbuch

1. Einleitung

Thank you for choosing the OLIGHT Baldr Mini. This ultra-compact white light and green beam combo is designed for optimal performance and versatility, integrating the compatibility of the PL-Mini 2 with the accuracy of the BALDR Pro. This manual provides detailed instructions for safe operation, installation, maintenance, and troubleshooting to ensure you get the most out of your device.

Packungsinhalt:

• BALDR Mini (battery built-in) x 1
• Picatinny (MIL-STD-1913) Rail Mount Adapter x 1
• HM2.5*4.5 Socket Cap Screw x 2
• MCC (Magnetic Charging Cable) Special Edition x 1
• H1.5 Allen Wrench x 1
• Oval Point Set Screw x 1
• Cone Point Set Screw x 1
• Benutzerhandbuch x 1

2. Wichtige Sicherheitshinweise

Please read this section carefully before using the product. Failure to follow these instructions may result in serious injury or property damage.

• Lasersicherheit: This product contains a Class IIIA laser with an output of <5mW. NICHT Blicken Sie direkt in den Laserstrahl. NICHT point the laser at people or animals. Avoid direct eye exposure.
• Augenschutz: Always wear appropriate eye protection when operating or testing the laser in a controlled environment.
• Kinder: Außerhalb der Reichweite von Kindern aufbewahren. Dies ist kein Spielzeug.
• Hitze: The device may become warm during prolonged use. Avoid direct contact with hot surfaces.
• Batterie: The built-in lithium polymer battery is not user-replaceable. Do not attempt to disassemble or modify the battery. Use only the provided Magnetic Charging Cable (MCC) for charging.
• Wasserbeständigkeit: The device is designed to be water-resistant, but it is not intended for underwater use. Do not submerge.
• Demontage: Do not disassemble the product. This will void the warranty and may cause damage.

3. Einrichtung und Installation

3.1 Erstaufladung

Before first use, fully charge the Baldr Mini. Connect the Magnetic Charging Cable (MCC) Special Edition to the magnetic charging port located at the bottom of the device. Connect the other end of the MCC to a USB power source. The indicator light on the MCC will turn red during charging and green when fully charged. A full charge typically takes approximately 1 hour.

The device features a low battery indicator. When the battery level is low, the indicator will alert you that it's time to recharge.

3.2 Schienenmontage

The Baldr Mini comes with two types of rail adapters: one for Glock rails and one for Picatinny (MIL-STD-1913) rails. Select the appropriate adapter for your firearm.

1. Attach Rail Adapter: Secure the chosen rail adapter to the Baldr Mini using the provided HM2.5*4.5 Socket Cap Screws and H1.5 Allen Wrench.
2. Montage an der Schiene: Open the quick attach/detach mount lever on the Baldr Mini. Align the device with the rail on your firearm. Close the lever firmly to secure the device.
3. Adjust Sliding Rail: The Baldr Mini features an adjustable sliding rail. Loosen the set screw (Oval Point or Cone Point, depending on preference) on the side of the device using the Allen wrench. Slide the light forward or backward along the rail to achieve the optimal position for your setup. Once positioned, tighten the set screw to lock it in place.

Abbildung 1: Placeholder image representing the OLIGHT Baldr Mini. This image would typically show the device being mounted onto a firearm rail, illustrating the quick attach/detach mechanism and the adjustable sliding rail feature. The actual product is a compact pistol light and green laser combo.

4. Bedienungsanleitung

The Baldr Mini is equipped with dual rear switches for easy operation by either hand.

4.1 Ein-/Ausschalten

• Momentan eingeschaltet: Press and hold either of the dual rear switches. The light/laser will remain on as long as the switch is held. Release to turn off.
• Konstant-Ein: Quickly single-press either of the dual rear switches. The light/laser will remain on until pressed again.

4.2 Modusauswahl

The Baldr Mini offers three modes: White Light Only, Green Beam Only, and Green Beam & White Light Combined.

• To cycle through modes, quickly double-press either of the dual rear switches while the device is on. The device will cycle through the available modes in sequence.
• The device will remember the last used mode when turned off and on again.

5. Wartung

5.1 Laden

Regularly charge your Baldr Mini to ensure optimal performance. Use only the provided Magnetic Charging Cable (MCC). The low battery indicator will signal when charging is required.

5.2 Reinigung

Keep the lens and laser aperture clean for clear output. Use a soft, clean cloth to wipe away dust or debris. For stubborn marks, a slightly damp Ein Tuch kann verwendet werden, anschließend sollte es sofort getrocknet werden. Verwenden Sie keine scharfen Chemikalien oder Scheuermittel.

5.3 Speicherung

Store the Baldr Mini in a cool, dry place away from direct sunlight and extreme temperatures. If storing for an extended period, ensure the battery is partially charged (around 50%) to prolong its lifespan.

6. Fehlerbehebung

If you encounter issues with your OLIGHT Baldr Mini, please refer to the following common problems and solutions:

If your issue is not listed or persists after attempting these solutions, please contact OLIGHT customer support for further assistance.

7. Spezifikationen

8. Garantie und Support

OLIGHT stands behind the quality of its products. For detailed information regarding the warranty policy for your Baldr Mini, please visit the official OLIGHT webBesuchen Sie die Website oder kontaktieren Sie direkt deren Kundendienst.

Offizieller OLIGHT-Standard WebWebsite: www.olightstore.com

For technical support, service, or warranty claims, please refer to the contact information provided on the official webWebsite oder der Produktverpackung.