Einführung
Bild: Star 025191 High Performance Pool Pump. This image displays the complete pool pump unit, highlighting its compact design and key components like the motor, pump housing, and transparent strainer lid.
This manual provides essential information for the safe and efficient installation, operation, and maintenance of your Star 025191 High Performance Pool Pump. This pump is designed for use with in-ground or above-ground swimming pools up to 53,000 gallons, ensuring water clarity and hygiene. Please read this manual thoroughly before installation and operation.
The Star 025191 pump features a 1.5 HP single-speed motor, factory-wired for 230 Volts, and is constructed from corrosion-resistant thermoplastic for durability. It delivers a high volume flow rate of up to 110 GPM at 20’ TDH for efficient water circulation to filtration systems.
Wichtige Sicherheitshinweise
Bei der Installation und Verwendung dieser elektrischen Geräte müssen stets grundlegende Sicherheitsvorkehrungen getroffen werden, darunter die folgenden:
- Lesen und befolgen Sie alle Anweisungen.
- GEFAHR: Risk of electrical shock. Connect only to a grounded receptacle protected by a ground-fault circuit interrupter (GFCI).
- WARNUNG: Um das Verletzungsrisiko zu verringern, erlauben Sie Kindern nicht, dieses Produkt zu benutzen.
- WARNUNG: This pump is for permanent installation only. Do not use with storable pools.
- Ensure the electrical supply matches the pump's voltage requirements (115V or 230V). The pump is factory-wired for 230V.
- All wiring must be performed by a qualified electrician and comply with local codes and regulations.
- Always disconnect power to the pump before servicing or performing maintenance.
- Die Pumpe darf nicht in Betrieb genommen werden, wenn sie in irgendeiner Weise beschädigt ist.
- Keep all connections dry and away from water.
Packungsinhalt
Vergewissern Sie sich vor Beginn der Installation, dass alle Komponenten im Paket vorhanden sind.
Bild: Package Contents Diagram. This illustration details the main pump unit (A) and the included connection accessories: 2-inch slip union adapters (B), 1.5-inch slip union adapters (C), and couplings (D).
| Artikel | Beschreibung | Menge |
|---|---|---|
| A | Star 025191 Pool Pump | 1 |
| B | 2" Slip Union Adapters | 2 |
| C | 1.5" Slip Union Adapters | 2 |
| D | Kupplungen | 2 |
Setup und Installation
Proper installation is crucial for the pump's performance and longevity. Refer to the installation diagram and follow these steps carefully.
1. Standortauswahl
- Install the pump as close to the pool as possible to minimize friction loss from long suction lines.
- Ensure the pump is installed on a firm, level base that can support its weight and prevent vibration.
- Provide adequate ventilation around the motor for cooling.
- Protect the pump from excessive moisture and direct sunlight.
2. Sanitäranschlüsse
The pump is designed to connect to either 1.5-inch or 2-inch pipe using the included slip union adapters and couplings.
- Apply thread sealant to all threaded connections to ensure a watertight seal.
- Connect the appropriate slip union adapters (1.5" or 2") to the pump's inlet and outlet ports.
- Use the couplings to connect the pump to your existing pool plumbing. Ensure all connections are tight to prevent air leaks, especially on the suction side.
Bild: Installation Diagram and Performance Data. This image provides a visual guide for connecting the pump to an in-ground pool system and includes a table detailing the pump's flow rate (GPM) at various Total Dynamic Head (TDH) levels.
3. Elektrische Anschlüsse
The Star 025191 pump is factory-wired for 230 Volts. If your electrical supply is 115 Volts, consult a qualified electrician for proper rewiring. The pump includes a 3 ft pigtail cord with ring terminals for connection.
- Ensure the power supply is disconnected at the circuit breaker before making any electrical connections.
- Connect the pump's pigtail cord to a dedicated circuit protected by a Ground-Fault Circuit Interrupter (GFCI).
- All electrical connections must comply with national and local electrical codes.
Bedienungsanleitung
1. Die Pumpe vorbereiten
Before starting the pump for the first time, or after the pump has been drained, it must be primed.
- Ensure the pool water level is adequate.
- Open all suction and return valves in the pool plumbing system.
- Remove the transparent strainer cover and fill the strainer basket housing with water until it overflows.
- Replace the strainer cover, ensuring it is securely tightened to prevent air leaks.
- Turn on the power to the pump. The pump should begin to draw water and expel air from the return lines.
- If the pump does not prime within 5 minutes, turn it off, re-prime, and check for air leaks in the suction line.
2. Normalbetrieb
- Once primed, the pump will operate continuously, circulating water through your filtration system.
- Monitor the pressure gauge on your filter (if applicable) to ensure it is within the normal operating range. An unusually high pressure reading may indicate a dirty filter or blockage.
- Regularly check the transparent strainer cover to see if the basket needs cleaning.
Wartung
Regular maintenance ensures optimal performance and extends the life of your pool pump.
1. Cleaning the Strainer Basket
The large strainer basket is designed to collect debris before it reaches the pump impeller. The transparent cover allows for easy visual inspection.
- Schalten Sie die Pumpe aus und trennen Sie die Stromzufuhr am Sicherungsautomaten.
- Rotate the transparent strainer cover counter-clockwise to remove it.
- Heben Sie den Siebkorb heraus und leeren Sie ihn, um eventuell angesammelte Rückstände zu entfernen.
- Spülen Sie den Korb gründlich mit Wasser aus.
- Inspect the O-ring on the strainer cover for cracks or wear. Replace if necessary.
- Place the clean basket back into the housing, ensuring it is seated correctly.
- Replace the strainer cover, tightening it clockwise until snug. Do not overtighten.
- Re-prime the pump as described in the "Operating Instructions" section.
2. Winterfestmachung
If you live in an area where temperatures drop below freezing, proper winterization is essential to prevent damage.
- Pumpe ausschalten und Stromzufuhr unterbrechen.
- Drain all water from the pump by removing the drain plugs (if applicable) or by disconnecting plumbing.
- Store the pump in a dry, protected area, or cover it securely if it must remain outdoors.
Fehlerbehebung
This section addresses common issues you might encounter with your pool pump. For problems not listed here, contact customer support.
| Problem | Mögliche Ursache | Lösung |
|---|---|---|
| Pumpe startet nicht | No power; tripped circuit breaker/GFCI; faulty motor. | Check power supply; reset breaker/GFCI; consult electrician. |
| Pump runs but does not prime or moves little water | Air leak in suction line; low water level; clogged strainer basket; closed valves. | Check all connections for leaks; ensure adequate pool water level; clean strainer basket; open all valves. |
| Übermäßige Geräusche oder Vibrationen | Air leak; cavitation; worn bearings; debris in impeller. | Check for air leaks; ensure proper water flow; contact service for worn parts. |
| Wasser tritt aus der Pumpe aus | Loose connections; worn O-rings/seals; cracked housing. | Verbindungen festziehen; O-Ringe/Dichtungen ersetzen; bei Gehäuseschäden den Kundendienst kontaktieren. |
Technische Daten
Detailed technical specifications for the Star 025191 High Performance Pool Pump.
Bild: Product Dimensions and Specifications. This image provides a detailed technical drawing with key dimensions of the pump and a table summarizing its electrical and performance characteristics.
| Spezifikation | Wert |
|---|---|
| Modellnummer | 025191 |
| Pferdestärken (PS) | 1.5 PS |
| Motortyp | Einzelgeschwindigkeit |
| Bandtage | 115/230V (Factory wired for 230V) |
| Phase | 1 |
| Durchflussrate (Max.) | 110 GPM @ 20' TDH (6,000 GPH) |
| Material | Corrosion-resistant Thermoplastic |
| Entladungsgröße | 1.5" or 2" (adapters included) |
| Kabellänge | 3 ft pigtail with ring terminals |
| Thermischer Schutz | Ja |
| Gesamtabmessungen | 26.5" x 9.45" x 12.6" |
| Gewicht | Ungefähr 50 kg |
| UPC | 054757100056 |
Garantie
The Star 025191 High Performance Pool Pump is covered by a 1 Jahr eingeschränkte Garantie Diese Garantie gilt ab Kaufdatum und deckt Material- und Verarbeitungsfehler bei normalem Gebrauch und ordnungsgemäßer Wartung ab.
For warranty claims or to understand the full terms and conditions, please refer to the warranty card included with your product or contact Star Water Systems customer support.
Note: This product is not available for shipment to California.
Kundenservice
For technical assistance, replacement parts, or warranty inquiries, please contact Star Water Systems customer support.
- WebWebsite: www.starwatersystems.com (Examp(der tatsächliche Link kann abweichen)
- Telefon: Beachten Sie die Angaben auf Ihrer Produktverpackung oder in den Herstellerangaben. webWebseite für aktuelle Kontaktnummern.
When contacting support, please have your model number (025191) and date of purchase readily available.
