Produkt überview
The Lepro Solar Motion Sensor Light is an advanced outdoor lighting solution designed for gardens, yards, and garages. It features a 2-in-1 design allowing for integrated or separate solar panel installation, ensuring optimal solar energy absorption. Equipped with high-sensitivity motion and optical sensors, it provides bright 1000LM illumination with 3 adjustable heads for a wide 270-degree lighting angle. The light is remote-controlled and offers two versatile lighting modes: AUTO and DIM-AUTO. Built with robust ABS material and an IP65 waterproof rating, it is designed to withstand various weather conditions, offering reliable and energy-efficient outdoor lighting.
Image: The Lepro Solar Motion Sensor Light, showcasing its main unit with three adjustable light heads, a motion sensor, and a separate solar panel connected by a cable. A remote control is also visible, indicating its control capabilities.
Setup und Installation
The Lepro Solar Motion Sensor Light offers flexible installation options: an integrated type or a separated type, depending on your needs and the best location for solar panel exposure.
Installationsoptionen:
- Integrated Type: The solar panel is directly attached to the light unit. This is suitable for areas where the light unit itself receives ample direktes Sonnenlicht.
- Separated Type: The solar panel can be detached from the light unit and placed up to 3 meters away using the provided cable. This is ideal for situations where the light needs to be installed in a shaded area (e.g., under eaves) but the solar panel can be positioned in direct sunlight for optimal charging.
Image: Illustration of the two installation types: Integrated (solar panel attached to light) and Separate (solar panel connected via cable), highlighting the flexibility of placement.
Image: A visual comparison demonstrating how a separate solar panel (top) can achieve better energy absorption by being placed in direct sunlight, compared to an integrated panel (bottom) which might be obstructed by eaves.
Empfohlene Installationshöhe:
For optimal motion detection and light coverage, install the unit at a height of 1.8 to 2.5 meters (approximately 6 to 8 feet) vom Boden.
Installationsschritte:
- Ort wählen: Wählen Sie einen Standort aus, der empfängt ample direct sunlight for the solar panel (at least 6 hours daily) and provides the desired lighting coverage.
- Bohrpunkte markieren: Use the provided mounting bracket to mark the drilling points on the wall.
- Bohrlöcher: Bohren Sie an den markierten Stellen Löcher und setzen Sie die Dübel ein.
- Halterung: Secure the light holder or panel holder to the wall using the provided screws.
- Attach Light/Panel: Attach the solar light unit and/or solar panel to their respective holders.
- Connect Cable (for Separated Type): If using the separated type, connect the 3-meter cable from the solar panel to the light unit. Ensure the connection is secure.
- Köpfe anpassen: Adjust the three light heads to your desired angles for optimal illumination. The heads offer up to 270 degrees of rotation.
- Aktivieren: Use the remote control or the switch on the unit to select the desired operating mode.
Image: Step-by-step visual guide for installing the light in its integrated configuration, showing how to mount the unit directly to a wall.
Image: Step-by-step visual guide for installing the light in its separated configuration, illustrating how to mount the light unit and the solar panel separately.
Bedienungsanleitung
The Lepro Solar Motion Sensor Light is designed for intelligent and efficient operation, primarily controlled via the included remote.
Bewegungs- und Lichtsensor:
The light features an ultra-sensitive motion (PIR) sensor and a light sensor. It will only activate at night or in dark environments when motion is detected. The motion sensor has a sensing distance of 0-8 Meter and a wide sensing angle of 120 Grad.
Image: A diagram illustrating the motion sensor's detection range (0-8m) and angle (120 degrees) in front of a garage, showing how it detects people, pets, and vehicles.
Lighting Modes (via Remote Control):
Use the remote control to switch between the following modes:
- Automatikmodus:
In this mode, the light remains off when no motion is detected at night. When motion is detected, the light turns on at full 1000LM brightness. It automatically turns off after approximately 20 Sekunden of no further motion detection.
- DIM-AUTO Mode:
In this mode, the light stays on at a low 20LM dim brightness when no motion is detected at night. When motion is detected, it brightens to full 1000LM brightness. After approximately 20 seconds of no further motion, it returns to the dim 20LM state.
- EIN/AUS-Tasten:
The remote also includes dedicated ON and OFF buttons for manual control of the light.
Image: A visual representation of the two practical lighting modes: AUTO mode (light off, then 1000LM with motion, then off) and DIM-AUTO mode (20LM dim, then 1000LM with motion, then back to 20LM dim).
Wartung
Proper maintenance ensures the longevity and optimal performance of your Lepro Solar Motion Sensor Light.
Reinigung:
- Wischen Sie das Solarpanel regelmäßig mit einem weichen, fusselfreien Tuch ab.amp cloth to remove dust, dirt, leaves, or snow. A clean solar panel ensures maximum sunlight absorption and efficient charging.
- Clean the light heads and motion sensor lens periodically to ensure clear light output and accurate motion detection.
Akku und Laden:
- Ensure the solar panel is placed in a location that receives at least 6 hours of direct sunlight daily for optimal charging.
- The light is designed to operate reliably even in rainy or winter months, but prolonged periods of low sunlight may reduce performance.
Haltbarkeit und Wetterbeständigkeit:
The light is constructed with robust ABS material and has an Wasserdichtigkeit gemäß IP65, making it resistant to rain, heat, and frost. No special weather-proofing maintenance is typically required beyond ensuring proper installation and avoiding physical damage.
Image: Visual representation of the light's IP65 waterproof rating under rain, and its heat and frost resistance in different weather conditions.
Fehlerbehebung
If you encounter issues with your Lepro Solar Motion Sensor Light, refer to the following common problems and solutions:
| Problem | Mögliche Ursache | Lösung |
|---|---|---|
| Das Licht geht nachts nicht an. |
|
|
| Das Licht bleibt schwach oder schaltet sich zu schnell ab. |
|
|
| Fernbedienung funktioniert nicht. |
|
|
| Das Licht ist nicht so hell wie erwartet. |
|
|
Technische Daten
| Besonderheit | Detail |
|---|---|
| Marke | Lepro |
| Modellnummer | PR640005-DW-2 |
| Helligkeit | 1000 Lumen |
| Farbtemperatur | 6500K (Cool White) |
| Stromquelle | Solarbetrieben |
| Reichweite des Bewegungssensors | 0-8 Meter |
| Bewegungssensorwinkel | 120 Grad |
| Lighting Angle (Adjustable Heads) | Bis zu 270 Grad |
| Wasserdichtigkeit | IP65 |
| Material | Kunststoff (ABS) |
| Technische Daten | 14 x 12 x 11 cm; 1.03 kg |
| Akku-Typ | 1 Lithium-Ionen-Batterie (erforderlich) |
| Farbe | Schwarz |
| Spezifische Verwendungen | Garden, Yard, Pathway, Patio |
Image: Detailed diagram showing the dimensions of the solar panel and light heads, along with a list of included components such as screws, wall plugs, light holders, panel holders, remote control, and the instruction manual.
Garantie und Support
Lepro is committed to providing reliable and satisfying lighting products. For specific warranty information, including duration and terms, please refer to the product packaging or the official Lepro website. Typically, warranty details cover manufacturing defects and product malfunctions under normal use.
For technical support, troubleshooting assistance beyond this manual, or warranty claims, please contact Lepro customer service through their official channels. Contact information can usually be found on the product packaging, the brand's official website, or the retailer's support page where the product was purchased.
Besuchen Sie die Lepro Store on Amazon Für weitere Informationen und Produktaktualisierungen.
