1. Einleitung
This manual provides essential information for the safe and effective installation, operation, and maintenance of your Okin JLDQ.10.435.250I recliner bed actuator motor. Please read these instructions thoroughly before proceeding with installation or use to ensure proper function and longevity of the product.
2. Produktüberschreitungview
The Okin JLDQ.10.435.250I is a refined linear actuator motor designed for recliner beds and power lift chairs. It serves as a direct replacement for specific Okin JLDQ series motors. The actuator motor set includes one motor unit and two connectors: a 5-pin round plug for the switch hand control and a 2-pin square plug with a clip for the power supply.
Image 2.1: The Okin JLDQ.10.435.250I recliner bed actuator motor.
Image 2.2: Close-up of the 2-pin power supply plug and 5-pin recliner switch plug.
3. Spezifikationen
| Besonderheit | Detail |
|---|---|
| Modell | JLDQ.10.435.250I |
| Aussehen | Schwarz (PA), Silberweiß (Aluminium) |
| Schlaganfall | 250 mm |
| Mindestabmessungen (Verkleinerung) | 435 mm |
| Maximum Dimensions (Extended) | 685 mm |
| Last (Schubkraft) | 1000 N |
| Last (Zugkraft) | 1000 N |
| Betriebsfrequenz | An 1 Minute / Aus 8 Minuten |
| Leistungsaufnahme | 24V === 50W (as per label) |
| Seriennummer Example | 21053376. Quartal 00006 |
Image 3.1: Product label showing model number JLDQ.10.435.250I und technische Daten.
4. Kompatibilität
This Okin JLDQ.10.435.250I motor is designed as a replacement for the original Okin JLDQ motor, model JLDQ.10.435.250I. It can also replace the following models, though minor differences may exist that do not affect general use:
- JLDQ.19B.435.250D02
- JLDQ.19B.435.250D03
- JLDQ.19B.435.250D04
- JLDQ.10.435.250
- JLDQ.3.435.250
- Serie 1.28.000.110.30
Wichtig: Always verify your existing motor's brand, model, minimum install dimension, stroke, and plug types to ensure compatibility with the replacement unit. Different actuators may not be compatible with all recliner frames.
5. Sicherheitshinweise
Bitte beachten Sie folgende Sicherheitsvorkehrungen:
- Ensure the power supply is disconnected before attempting any installation, maintenance, or troubleshooting.
- Dieser Motor ist nur für den Innenbereich geeignet.
- Do not operate the motor if any part is damaged or if the cables are frayed.
- Halten Sie Hände und lose Kleidung während des Betriebs von beweglichen Teilen fern.
- Connection is only to class 2 DC circuit.
- Wenn Sie sich bei einem Arbeitsschritt unsicher sind, konsultieren Sie einen qualifizierten Techniker.
6. Installation
The installation process is generally straightforward. Follow these steps:
- Stromversorgung trennen: Unplug the recliner or bed from the main power outlet.
- Zugangsmotor: Carefully position the recliner to access the existing motor. This may involve tilting the chair or removing a fabric cover.
- Alten Motor abklemmen:
- Disconnect the 5-pin round plug from the hand control.
- Disconnect the 2-pin square plug from the power supply.
- Unbolt or unclip the old motor from the recliner frame.
- Alten Motor ausbauen: Carefully remove the old actuator motor from the recliner mechanism.
- Neuen Motor einbauen:
- Position the new Okin JLDQ.10.435.250I motor in the same location as the old one.
- Securely bolt or clip the new motor to the recliner frame.
- Neuen Motor anschließen:
- Verbinden Sie den 5-poligen Rundstecker mit der Handsteuerung.
- Connect the 2-pin square plug with the clip to the power supply. Ensure a secure connection.
- Testfunktionalität: Reconnect the recliner to the power outlet and test the motor's operation using the hand control. Ensure smooth extension and retraction.
Abbildung 6.1: Seite view of the motor, showing mounting points and overall structure.
Bild 6.2: Schräg view of the motor, illustrating its compact design for installation.
7. Bedienung
Once installed and connected, operate the recliner motor using the hand control unit. Press the appropriate buttons on the hand control to extend or retract the recliner mechanism. The motor is designed for intermittent use with an operation frequency of "On 1 min / Off 8 min" to prevent overheating and ensure longevity.
Image 7.1: Visual representation of the motor's features and its application in a recliner chair.
8. Wartung
The Okin JLDQ.10.435.250I motor requires minimal maintenance:
- Reinigung: Keep the motor free from dust and debris. Wipe with a dry cloth. Do not use liquid cleaners directly on the motor.
- Inspektion: Periodically inspect the motor and all connections for any signs of wear, damage, or loose fittings.
- Schmierung: Der Motor ist werkseitig geschmiert und benötigt im Allgemeinen keine zusätzliche Schmierung.
9. Fehlerbehebung
If your recliner motor is not functioning correctly, consider the following:
- Kein Strom:
- Ensure the recliner is securely plugged into a working power outlet.
- Prüfen Sie das Netzteil auf Kontrollleuchten oder Anzeichen von Beschädigungen.
- Verify the 2-pin square plug connection to the power supply is firm.
- Motor reagiert nicht:
- Check the 5-pin round plug connection to the hand control.
- Inspect the hand control for damage or stuck buttons.
- Ensure the motor is not jammed by any obstructions in the recliner mechanism.
- Motorüberhitzung:
- Adhere to the "On 1 min / Off 8 min" operation frequency. Excessive continuous use can cause overheating.
- Sorgen Sie für ausreichende Belüftung rund um den Motor.
- Ungewöhnliche Geräusche:
- Disconnect power and inspect the motor and recliner mechanism for any loose parts or foreign objects.
Wenn die Schritte zur Fehlerbehebung das Problem nicht lösen, wenden Sie sich bitte an den Kundendienst.
10. Garantie und Support
For warranty information, technical support, or to inquire about replacement parts, please refer to the official Okin brand store or contact your retailer. Keep your purchase receipt for warranty claims.
Visit the official Okin Store: Okin Store auf Amazon
