Veepeak 1220 12V Autobatterietester – Benutzerhandbuch

1. Einleitung

The Veepeak 1220 12V Car Battery Tester is a versatile diagnostic tool designed to assess the health of 12V lead-acid batteries and their associated charging and cranking systems. It provides quick and accurate readings for various battery types, helping users determine if a battery is in good condition, needs recharging, or requires replacement. This manual provides detailed instructions for the proper use and maintenance of your Veepeak 1220 Battery Tester.

2. Produktüberschreitungview

Abbildung 1: Veepeak 1220 12V Car Battery Tester. This image shows the compact red device with its display screen, navigation buttons (ESC, OK, up, down), and attached red and black battery clamps.

2.1 Was ist in der Box?

• Battery tester with clamps and cord
• Benutzerhandbuch (dieses Dokument)

2.2 Hauptmerkmale

• Batteriezustandsprüfung: Scans and displays the overall status of a 12V auto battery, including State of Charge (SOC), State of Health (SOH), voltage, Innenwiderstand und Kaltstart Amps (CCA).
• Alternator & Starting System Tester: Reads ripple, loaded, and unloaded voltage to assess alternator performance and checks cranking voltage and time for starting capability.
• Plug and Play & High Accuracy: Tests batteries (even dead ones) in-vehicle or out-of-vehicle with high accuracy (close to 0.01V with overall accuracy close to 99.9%).
• Breite Kompatibilität: Compatible with all 12V lead-acid batteries from 100 to 2000 CCA (Regular Flooded, AGM Flat Plate, AGM Spiral, GEL, EFB).
• Sicherheitsmerkmale: Includes polarity reverse protection and is spark-proof with no heat connection.

3. Einrichtung

Before using the Veepeak 1220 Battery Tester, ensure the battery terminals are clean and free of corrosion for accurate readings.

1. Identify the positive (+) and negative (-) terminals on the 12V battery.
2. Verbinden Sie die roteamp des Testers an den Pluspol (+) der Batterie anschließen.
3. Verbinden Sie die schwarzeamp des Testers an den Minuspol (-) der Batterie anschließen.
4. The tester will automatically power on once connected. The main menu will appear on the screen.

Notiz: The device features polarity reverse protection, meaning it will not be damaged if the clamps are connected incorrectly. However, always strive for correct connection for safety and proper operation.

4. Bedienungsanleitung

Navigate the menu using the Up/Down arrow buttons and confirm selections with the OK button. Use the ESC button to go back to the previous screen.

4.1 Batterietest

Dieser Test beurteilt den allgemeinen Zustand Ihrer Batterie.

Abbildung 2: Multi-Functional 12V Battery Analyzer. The screen displays options for Battery Test, Cranking Test, and Charging Test.

1. Wählen Sie im Hauptmenü „1. Batterietest“ und drücken Sie OK.
2. Select the appropriate battery type (e.g., Regular Flooded, AGM Flat Plate, AGM Spiral, GEL, EFB) and press OK.
   

   Abbildung 3: Compatible Battery Types selection screen.

3. Geben Sie den Kaltstart ein Amps (CCA) rating of your battery. This information is usually found on the battery label. Use the Up/Down arrows to adjust the value and OK to confirm.
4. The tester will perform the test and display the results, including SOH, SOC, internal resistance, and voltage. It will also indicate if the battery is "GOOD BATTERY", "RECHARGE", or "REPLACE".

4.2 Anlasstest

Dieser Test bewertet die Fähigkeit der Batterie, den Motor zu starten.

Abbildung 4: Cranking Test in progress. The screen shows cranking time and voltage.

1. From the Main Menu, select "2. Cranking Test" and press OK.
2. The screen will prompt "Start Engine".
3. Starten Sie den Motor des Fahrzeugs.
4. The tester will automatically detect the cranking event and display the cranking time and voltage. It will indicate if the cranking is "GOOD" or "LOW".

4.3 Ladesystemtest

This test checks the alternator and the vehicle's charging system.

Abbildung 5: Charging System Test screen showing loaded, unloaded voltage und Wellen.

1. From the Main Menu, select "3. Charging Test" and press OK.
2. The screen will prompt for a "Ripple Test". Press OK.
3. The screen will then prompt "Increase RPM to 2500 R/min and keep it 5 seconds. Press OK to continue."
4. With the engine running, increase the engine RPM to approximately 2500 for 5 seconds. It is recommended to have a second person assist with this step.
5. Press OK. The tester will display the loaded voltage, unbeladenes Volumentage, and ripple. It will indicate if the charging is "HIGH", "NORMAL", or "LOW".

5. Wartung

• Keep the tester clean and dry. Wipe it with a soft, damp mit einem sauberen Tuch abwischen.
• Bewahren Sie den Tester an einem kühlen, trockenen Ort fern von direkter Sonneneinstrahlung und extremen Temperaturen auf.
• Überprüfen Sie regelmäßig die Kabel und Anschlüsse.ampPrüfen Sie auf Anzeichen von Beschädigung oder Abnutzung. Ersetzen Sie das Teil gegebenenfalls.
• Ensure the battery terminals are clean before testing to prevent inaccurate readings.

6. Fehlerbehebung

7. Spezifikationen

• Produktabmessungen: 5.06 x 2.85 x 0.87 Zoll
• Artikelgewicht: 10.23 Unzen
• Energiequelle: Batteriebetrieben (mit getesteter Batterie)
• Mindest. Betriebsvoltage: 12 Volt
• CCA-Bereich: 100-2000 CCA
• Kompatible Batterietypen: Normal geflutet, AGM-Flachplatten, AGM-Spiralplatten, GEL, EFB
• Hersteller: Veepeak

8. Garantie und Support

The Veepeak 1220 12V Car Battery Tester comes with a einjährige problemlose Ersatzgarantie.

For technical support, troubleshooting assistance, or warranty claims, please contact Veepeak customer service through their official webWebsite oder den Händler, bei dem das Produkt gekauft wurde.

Bitte bewahren Sie Ihren Kaufbeleg für Garantiezwecke auf.