Einführung
Thank you for choosing the Perlegear PGTVS29 Single Monitor Stand. This freestanding monitor mount is designed to enhance your workspace by providing versatile positioning for your 13-34 inch screens. With features like 360-degree rotation, 5 ergonomic height settings, and adjustable swivel and tilt, this stand offers optimal viewing flexibility and improved posture. Please read this manual carefully before installation and use to ensure safe and correct operation.
Wichtige Sicherheitsinformationen
Please read all instructions carefully before assembly. If you do not understand these instructions or have doubts about the safety of the installation, please contact a qualified installer. Check for any missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose not explicitly specified in this manual.
- Gewichtskapazität: Die maximale Tragfähigkeit von 44 lbs (20 kg) darf nicht überschritten werden.
- Bildschirmgröße: Kompatibel mit Bildschirmen von 13 bis 34 Zoll.
- VESA-Kompatibilität: Supports VESA mounting patterns 50x50mm and 100x100mm. Verify your screen's VESA pattern before installation.
- Stabilität: Stellen Sie sicher, dass der Ständer auf einer stabilen, ebenen Fläche steht, um ein Umkippen zu verhindern.
- Kinder: Keep children away from the assembly area. Small parts may be swallowed.
Packungsinhalt
Please check that all components are included and undamaged. If any parts are missing or damaged, contact Perlegear customer support.
- Support Pillar (1)
- Tempered Glass Base (1)
- VESA-Platte (1)
- Montagesatz (Schrauben, Unterlegscheiben, Distanzstücke)
- Kabelklemmen (2)
- Assembly Tools (Allen key, screwdriver)
- Bedienungsanleitung (1)
Setup und Installation
Follow these steps to assemble your Perlegear PGTVS29 Monitor Stand.
Step 1: Attaching the VESA Plate to Your Monitor
Determine the correct screws and spacers for your monitor's VESA mounting holes. For flat-back screens, use appropriate screws directly. For curved screens or screens with a bump, use spacers to ensure a secure fit. Attach the VESA plate to the back of your monitor.
Step 2: Connecting the Support Pillar to the Base
Attach the foot pads to the matte side of the tempered glass base. Secure the support pillar to the tempered glass base using the provided screws, steel washers, and plastic washers. Ensure plastic washers contact the glass to prevent damage.
Schritt 3: Befestigen des Monitors an der Stützsäule
Carefully lift your monitor (with the VESA plate attached) and slide it onto the support pillar. Secure the monitor to the support pillar using the knob on the VESA plate. Ensure it clicks into place securely.
Montage-Videoanleitung
Video: Official Perlegear video demonstrating the assembly process and key features of the monitor stand, including attaching the VESA plate, connecting the pillar to the base, and mounting the screen.
Bedienungsanleitung
The Perlegear PGTVS29 Monitor Stand offers multiple adjustment options to customize your viewErfahrung.
Höhenverstellung
The monitor stand features 5 height settings, allowing you to adjust your screen from 9.27 inches to 15.26 inches tall. To adjust the height, loosen the knob on the support pillar, slide the monitor to your desired height, and then re-tighten the knob to secure it.
Neigungseinstellung
Adjust the screen tilt from -15° to +10° using the convenient tilt knob located on the VESA plate. Loosen the knob, adjust the screen to your preferred angle, and then tighten the knob to lock it in place.
Schwenkeinstellung
The screen can be swiveled manually +/-50° for ultimate viewing flexibility. Only swivel the screen by the screen edges; do not press on the screen itself.
360° Drehung
Rotate your screen a full 360° to switch between landscape and portrait orientations. This feature is compatible even with large 34-inch displays, though off-centered VESA patterns may affect perfect vertical orientation.
Kabelmanagement
Utilize the two included cable clips to route cables neatly along the back of the support pillar. This helps maintain a clean and organized workspace.
Wartung
To ensure the longevity and optimal performance of your Perlegear PGTVS29 Monitor Stand, follow these simple maintenance guidelines:
- Reinigung: Wischen Sie den Ständer mit einem weichen, fusselfreien Tuch ab.amp Tuch. Vermeiden Sie die Verwendung von Scheuermitteln oder Lösungsmitteln, da diese die Oberfläche beschädigen können.
- Befestigungsmaterial: Überprüfen Sie regelmäßig alle Schrauben und Verbindungen, um sicherzustellen, dass sie fest sitzen. Ziehen Sie sie gegebenenfalls nach.
- Bewegung: If any moving parts become stiff, apply a small amount of silicone-based lubricant to the joints.
Fehlerbehebung
Sollten Sie Probleme mit Ihrem Monitorständer haben, beachten Sie bitte die folgenden häufig auftretenden Probleme und Lösungen:
- Monitor is wobbly:
- Ensure all screws securing the monitor to the VESA plate and the pillar to the base are tightened.
- Verify the stand is on a flat, stable surface.
- Monitor does not tilt/swivel/rotate smoothly:
- Check if the tilt knob is sufficiently loosened before attempting to adjust.
- Apply a small amount of silicone lubricant to the moving joints if resistance persists.
- Monitor cannot be mounted:
- Confirm your monitor's VESA pattern matches the stand's compatibility (50x50mm or 100x100mm).
- Ensure your monitor's weight (max 44 lbs) and size (max 34 inches) are within the specified limits.
- Use the correct screws and spacers from the mounting hardware kit for your specific monitor.
If you are unable to resolve an issue, please contact our U.S.-based product support team for assistance.
Technische Daten
| Besonderheit | Detail |
|---|---|
| Marke | Prozessausrüstung |
| Modellnummer | PGTVS29 |
| Artikelgewicht | 4.95 Pfund (2.25 kg) |
| Verpackungsabmessungen | 17.65 x 9.02 x 2.8 Zoll |
| Farbe | Schwarz |
| Material | Metal and Tempered Glass Base |
| Montagetyp | Tischhalterung |
| Bewegungstyp | Schwenken |
| Kompatible Bildschirmgröße | 13-34 Zoll |
| Maximale Tragfähigkeit | 44 kg |
| VESA-Kompatibilität | 50x50mm, 100x100mm |
| Höheneinstellungen | 5 settings (9.27" to 15.26") |
| Neigungseinstellung | -15° bis +10° |
| Schwenkeinstellung | +/-50° |
| Drehung | 360° |
Garantie und Support
Perlegear stands behind the quality of its products. For specific warranty information, please refer to the product packaging or contact Perlegear customer service. If you have any questions, require technical assistance, or need to report missing/damaged parts, please contact our U.S.-based product support team. Contact details can typically be found on the product packaging or the official Perlegear webWebsite.
