Kenmore Washer Water Drain Pump Replacement Manual

Einführung

This manual provides essential information for the installation, operation, and maintenance of your replacement water drain pump, designed for compatibility with Kenmore Washer Model 110.26832692. Please read these instructions carefully before proceeding with installation or use to ensure proper function and safety.

Sicherheitshinweise

Always observe the following safety precautions when handling or installing the drain pump:

• Stromversorgung trennen: Before beginning any installation or maintenance, ensure the washer is unplugged from the electrical outlet to prevent electric shock.
• Wasserabsperrung: Turn off the water supply to the washer to prevent leaks.
• Schutzausrüstung tragen: Use appropriate personal protective equipment, such as gloves and eye protection, to avoid injury.
• Restwasser ablassen: Be prepared for residual water in the washer and hoses. Have towels and a bucket ready.
• Professionelle Hilfe: Wenn Sie sich bei einem der Schritte unsicher sind, wenden Sie sich an einen qualifizierten Haushaltsgerätetechniker.

Packungsinhalt

Ihr Paket sollte folgende Artikel enthalten:

• 1 x Washer Water Drain Pump (Replacement Part)

Installationsanleitung

Follow these steps carefully to replace the water drain pump in your Kenmore 110.26832692 washer. Refer to your washer's specific service manual for detailed diagrams if necessary.

1. Bereiten Sie die Waschmaschine vor: Trennen Sie die Waschmaschine vom Stromnetz und drehen Sie die Wasserzufuhr ab. Ziehen Sie die Waschmaschine von der Wand weg, um Zugang zur Rückseite zu erhalten.
2. Zugang zur Pumpe: Depending on your specific Kenmore 110.26832692 model, you may need to remove the front panel, rear panel, or tilt the washer back to access the drain pump located at the bottom. Consult your washer's service manual for exact access procedures.
3. Restwasser ablassen: Place a shallow pan or towels under the pump area to catch any remaining water in the hoses. Carefully disconnect the hoses attached to the old drain pump.
4. Alte Pumpe ausbauen: Locate the mounting screws or clips securing the old drain pump. Remove them and carefully detach the pump from its mounting bracket. Disconnect any electrical wiring connected to the pump.
5. Neue Pumpe einbauen: Connect the electrical wiring to the new drain pump. Ensure connections are secure. Mount the new pump onto the bracket using the original screws or clips.
6. Schläuche anschließen: Reattach the drain hoses to the new pump. Ensure all clamps werden festgezogen, um Lecks zu verhindern.
7. Unterlegscheibe wieder zusammenbauen: Reinstall any panels or covers that were removed to access the pump.
8. Testbetrieb: Reconnect the washer to the power supply and turn on the water. Run a short drain/spin cycle to check for proper operation and any leaks.

Funktionsprinzipien

The water drain pump is an integral component of your washing machine's drainage system. During the wash and rinse cycles, once the water needs to be expelled from the tub, the washer's control system activates the drain pump. The pump then draws water from the washer tub and forces it through the drain hose, effectively emptying the machine. Proper functioning of this pump ensures that water is removed efficiently, allowing the spin cycle to effectively remove moisture from your laundry.

Wartung

Um die Langlebigkeit und den effizienten Betrieb Ihrer Ablaufpumpe zu gewährleisten, beachten Sie bitte die folgenden Wartungstipps:

• Regelmäßige Reinigung: Periodically check the washer's drain filter (if accessible and present in your model) for lint, coins, or other debris that could obstruct the pump.
• Überladung vermeiden: Eine Überladung der Waschmaschine kann die Pumpe und andere Bauteile übermäßig belasten.
• Schläuche prüfen: Überprüfen Sie gelegentlich die Abflussschläuche auf Knicke, Verstopfungen oder Beschädigungen, die den Wasserdurchfluss behindern könnten.

Fehlerbehebung

If your washer is experiencing drainage issues after pump replacement, refer to the table below for common problems and potential solutions:

Wenn die Schritte zur Fehlerbehebung das Problem nicht lösen, wird empfohlen, einen qualifizierten Kundendiensttechniker für Haushaltsgeräte zu kontaktieren.

Technische Daten

• Produktart: Washer Water Drain Pump (Replacement Part)
• Kompatibilität: Kenmore Waschmaschine Modell 110.26832692
• Hersteller: 20 SECOND SOAP (Supplier of this replacement part)
• UPC: 689035815232
• ASIN: B0DBGGY267

Garantie und Support

For information regarding the warranty of this replacement part or for technical support, please refer to the documentation provided by the seller or manufacturer at the time of purchase. You may also contact the seller directly through the platform where the purchase was made.