BoxWave ClearTouch Kristall-Displayschutzfolie – Bedienungsanleitung

1. Produktüberschreitungview

The BoxWave ClearTouch Crystal Screen Protector is a high-quality, transparent film designed to protect the display of your Motorola APX 6000 from scratches, dust, and minor impacts. It offers 99% visual clarity, ensuring a clear and vibrant viewing experience without compromising screen sensitivity.

2. Lieferumfang

Ihr BoxWave ClearTouch Crystal Displayschutzfolien-Paket enthält folgende Artikel:

• Zwei (2) ClearTouch Kristall-Displayschutzfolien
• Eine (1) Applikatorkarte
• Ein (1) Mikrofasertuch
• Ein (1) Staubentfernungsaufkleber

3. Installationsanleitung

Follow these steps carefully for optimal application of your ClearTouch Crystal Screen Protector:

1. Reinigen Sie den Bildschirm: Use the included microfiber cleaning cloth to thoroughly wipe down the screen of your Motorola APX 6000. Ensure there are no dust particles, smudges, or fingerprints. For stubborn marks, a small amount of screen cleaner can be used, but ensure the screen is completely dry before proceeding.
2. Staub entfernen: Verwenden Sie den Staubentfernungsaufkleber, um verbliebene Staubpartikel vom Bildschirm zu entfernen. Tupfen Sie den Aufkleber leicht über die gesamte Bildschirmoberfläche.
3. Richten Sie den Schutz aus: Carefully peel back a small portion of the protective film (labeled '1' if present) from one end of the screen protector. Align the exposed edge of the screen protector with the corresponding edge of your device's screen. Pay close attention to cutouts for speakers, cameras, or sensors.
4. Nach und nach auftragen: Once aligned, slowly peel back the rest of the protective film (labeled '1') while simultaneously using the applicator card to smooth the screen protector onto the device's screen. Apply gentle, even pressure from the aligned edge outwards to push out any air bubbles.
5. Luftblasen entfernen: If air bubbles appear, use the applicator card to gently push them towards the nearest edge of the screen. For persistent bubbles, you may carefully lift a small section of the protector and reapply, smoothing it down with the card.
6. Letztes Schälen: Once the screen protector is fully applied and free of major bubbles, carefully peel off the top protective layer (labeled '2' if present).
7. Settle Time: The low-tack adhesive may take up to 48 hours to fully settle along the edges. Any initial minor air bubbles typically clear with regular use as the adhesive cures.

4. Gebrauch und Pflege

Once installed, the ClearTouch Crystal Screen Protector requires minimal special care. It is designed to be durable and maintain its clarity over time.

4.1. Täglicher Gebrauch

The screen protector will not interfere with the touch sensitivity or display quality of your Motorola APX 6000. Use your device as normal, enjoying the added layer of protection.

4.2. Reinigung

To clean the screen protector, use a soft, lint-free cloth, such as the included microfiber cloth. For smudges or fingerprints, you can lightly dampen the cloth with water or a mild, non-abrasive screen cleaner. Avoid harsh chemicals or abrasive materials, as these can damage the protector's surface.

4.3. Reusability

The ClearTouch Crystal screen protector features a glueless adhesive, allowing for reapplication if necessary. If you need to remove and reapply, do so carefully to avoid stretching or damaging the film. Ensure the screen and the protector's adhesive side are clean before reapplication.

5. Fehlerbehebung

Problem: Air bubbles after installation.

Lösung: Small bubbles often disappear within 24-48 hours as the adhesive settles. For larger bubbles, gently lift the nearest edge of the protector and reapply, using the applicator card to smooth it down from the lifted edge outwards. Ensure no dust is trapped underneath.

Problem: Dust particles trapped under the protector.

Lösung: Carefully lift the screen protector near the dust particle. Use the dust removing sticker to gently dab and lift the particle from both the screen and the adhesive side of the protector. Reapply the protector, smoothing it down with the applicator card.

Problem: Protector not adhering properly at edges.

Lösung: Ensure the edges of your device's screen are clean and free of oils or debris. Apply firm, even pressure with the applicator card along the edges. Allow up to 48 hours for the adhesive to fully cure. If the issue persists, ensure the protector is correctly aligned and not overlapping any curved surfaces if your device has them.

6. Spezifikationen

7. Garantie und Support

BoxWave products are designed for quality and durability. For specific warranty information regarding your ClearTouch Crystal Screen Protector, please refer to the packaging or visit the official BoxWave website. If you encounter any issues or have questions not covered in this manual, please contact BoxWave customer support through their official channels for assistance.

Bitte bewahren Sie Ihren Kaufbeleg für eventuelle Garantieansprüche auf.