Benutzerhandbücher+

BN-LINK CP-UWLD28

BN-LINK CP-UWLD28 Dimmer-Lichtschalter – Benutzerhandbuch

Model: CP-UWLD28 | Brand: BN-LINK

1. Einleitung

This manual provides instructions for the installation and operation of your BN-LINK CP-UWLD28 Dimmer Light Switch. This dimmer switch is designed for single-pole applications and requires a neutral wire for proper functionality. It supports dimmable LED, CFL, and incandescent light bulbs, offering two distinct dimming modes and a memory function to recall your last brightness setting.

2. Lieferumfang

  • 1x Dimmer Light Switch
  • 1x Wall Plate
  • 4x Drahtmuttern
  • 2x lange Schrauben
  • 2x kurze Schrauben
  • 1x Benutzerhandbuch (dieses Dokument)
Contents of the BN-LINK Dimmer Light Switch package including the dimmer switch, wall plate, wire nuts, and screws.

Image: The package contents, including the dimmer switch, wall plate, wire nuts, and mounting screws.

3. Spezifikationen

BesonderheitDetail
BetriebsmodusEIN-AUS
Aktuelle Bewertung3 Amps
Betriebslautstärketage125 Volt
Kompatible GeräteDimmable LED (3W-150W), CFL (3W-150W), Incandescent (3W-400W)
SteuerungstypManueller Druckknopf
KonnektivitätsprotokollN.A (No WiFi)
Abmessungen (L x B x H)4.49 x 2.76 x 1.34 Zoll
Artikelgewicht5 Unzen
FarbeWeiß
Diagram showing the dimensions of the BN-LINK Dimmer Light Switch.

Image: Product dimensions of the dimmer switch.

4. Installation

Wichtig: Installation should be performed by a qualified electrician or a person with knowledge of electrical wiring. Ensure power is turned off at the circuit breaker before beginning installation.

  1. Strom ausschalten: Locate the circuit breaker controlling the light switch you intend to replace and turn off the power. Verify the power is off using a voltage Tester.
  2. Alten Schalter entfernen: Carefully remove the existing wall plate and unscrew the old switch from the electrical box. Disconnect the wires from the old switch.
  3. Drähte identifizieren: Identify the following wires in your electrical box:
    • Leitungsdraht: Leitet Strom vom Leistungsschalter.
    • Lastkabel: Wird an die Leuchte angeschlossen.
    • Neutralleiter: Typically white, required for this dimmer switch.
    • Erdungskabel: Bare copper or green.
  4. Wire the Dimmer Switch: Connect the wires from the dimmer switch to the corresponding wires in the electrical box using the provided wire nuts. Refer to the wiring diagram below.
    • Dimmerschalter Weißer Draht to Wall Box Neutralleiter
    • Dimmerschalter Schwarzes Kabel to Wall Box Power Supply's Line (Live)
    • Dimmerschalter Rotes Kabel to Wall Box Draht laden
    • Dimmerschalter Grüner Draht to Wall Box Erdungskabel
  5. Montieren Sie den Schalter: Carefully push the wired dimmer switch into the electrical box. Secure it with the provided screws.
  6. Wandplatte installieren: Attach the new wall plate over the dimmer switch.
  7. Strom wiederherstellen: Schalten Sie den Strom am Leistungsschalter wieder ein.
Wiring diagram for the BN-LINK Dimmer Light Switch showing connections for ground, neutral, line, and load wires.

Image: Wiring diagram for single-pole installation. Ensure a neutral wire is available.

Note: This dimmer switch works in single-pole only and requires a neutral wire. It is not a smart dimmer switch and cannot be connected to Wi-Fi.

5. Bedienung

The BN-LINK Dimmer Light Switch features intuitive controls for adjusting light brightness and an indicator light for visibility in the dark.

Erste Verwendung

During the first use, press the power button on the dimmer switch. The initial brightness of the light is set at 100%. Use the "+" and "-" buttons for fast adjustments and fine adjustment.

Video: Demonstration of the BN-LINK Dimmer Light Switch's operation, including fast and fine dimming adjustments and memory function.

Kontrollen überview

Close-up image of the dimmer switch buttons with labels: Dimmer + button, Dimmer - button, and Power button, along with indicator lights.

Image: Labeled buttons on the dimmer switch for power, dimming up, and dimming down, with indicator lights.

  • Netzschalter: Press to turn the lighting On/Off.
  • Dimmer "+" Button:
    - Fast Adjustment: Press briefly to increase brightness by 10% each time.
    - Feineinstellung: Press and hold to gradually increase brightness by 1% each time.
  • Dimmer "-" Button:
    - Fast Adjustment: Press briefly to decrease brightness by 10% each time.
    - Feineinstellung: Press and hold to gradually decrease brightness by 1% each time.
  • Kontrollleuchten: Display the current brightness level (20%, 40%, 60%, 80%, 100%).
Image illustrating the two brightness adjustment modes: fast adjustment by 10% and fine adjustment by 1%.

Image: Visual representation of the fast (10% increments) and fine (1% increments) brightness adjustment modes.

Memory Funktion

The dimmer switch remembers the last brightness level used and restores it automatically the next time the light is turned on.

Image showing the dimmer switch with an indicator light, highlighting its visibility in low light conditions.

Image: The thoughtful indicator light helps locate the dimmer easily in the dark.

6. Kompatibilität

This dimmer switch is compatible with various dimmable light sources:

  • Dimmbare LED: 3-150W, 125V/60Hz
  • Dimmbare Energiesparlampe: 3-150W, 125V/60Hz
  • Glühlampe Lamp: 3-400W, 125V/60Hz

Please ensure that your fluorescent lamp und LED lamp are dimmable, and the total load of the bulbs is within the specified range.

Image showing various types of light bulbs including incandescent, LED, and CFL, indicating wide compatibility with the dimmer switch.

Image: Illustration of wide compatibility with incandescent, dimmable LED, and dimmable CFL bulbs.